Leviton Manufacturing Co. Inc. RZE06 用户手册

Single Pole (One location) or 3-Way (Multi-location)

Cat. No. RZEØ6-1L, 600W

120VAC, 60Hz

:

•  To be installed and/or used in accordance with appropriate electrical codes and regulations.
•  If you are unsure about any part of these instructions, consult a qualified electrician.
•  To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer-operated appliance.
•  Use with electronic low-voltage transformers only. Do Not use to control a magnetic low-voltage transformer. Use a Leviton magnetic low-voltage dimmer to control magnetic
  low-voltage transformers.
•  This dimmer provides protection from overheating. An excessive load applied to the dimmer will cause the dimmer to overheat. The excess load must be removed to resume proper 

operation.

•  Vizia™ RF dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ remotes or Vizia™ RF controllers for multi-location dimming.
•  Use only one (1) Vizia™ RF dimmer in a multi-location circuit with up to 9 Vizia™ coordinating remotes without LEDs or Vizia™ RF controllers. 

:

•  Lighting fixture and dimmer must be grounded.
•  This dimmer must be installed in a wall box with a neutral connection.
•  Consult fixture manufacturer to determine if their solid state transformers can be dimmed.
•  Total minimum load must exceed 40W.
•  Dimmer may feel warm to the touch during normal operation.
•  Recommended minimum wall box depth is 2-1/2".
•  Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).
•  Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
•  Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

IMPORTANT : For 3-Way applications, note that one of the screw 

terminals from the old switch being removed will usually be a different 

color (Black) or labeled Common. Tag that wire with electrical tape and 

identify as the common (Line or Load) in both the dimmer wall box and 

remote wall box.

1 - #12 w/ 1 to 3 #14, #16 or #18

2 - #12 w/ 1 or 2 #16 or #18

1 - #14 w/ 1 to 4 #16 or #18

2 - #14 w/ 1 to 3 #16 or #18

DI-000-RZE06-00A-X0

VZEØ6

600W

500W

400W

Slotted/Phillips Screwdriver 

Electrical Tape

Pliers 

 

 

Pencil

Cutters 

 

 

Ruler

When installing more than one dimmer in the same location, the 

side sections of the mounting strap must be removed. Use pliers to 

carefully bend side sections back and forth until they break off. The 

side sections dissipate heat, so removing them sometimes requires a 

derating of the dimmer’s capacity 

(refer to chart).

Pull off pre-cut insulation from dimmer leads. Make sure that 

the ends of the wires from the wall box are 

necessary). Remove insulation from each wire in the wall 

box as shown:

•  Green or bare copper wire in wall box to Green dimmer lead.

•  Line Hot wall box wire to Black dimmer lead.

•  Load wall box wire to Red dimmer lead.

•  Line Neutral wall box wire to White dimmer lead.

•  Yellow/Red wire should have Red insulation label affixed. 

 

NOTE: If insulating label is not affixed to Yellow/Red dimmer lead, 

use electrical tape to cover.

• 

NOTE: The dimmer must be installed in a wall box that has a Line 

Hot connection.

NOTE: Maximum wire length from dimmer to all installed remotes 

cannot exceed 300 ft (90 m).

•  Green or bare copper wire in wall box to Green dimmer lead.

•  Line Hot (common) wall box wire identified (tagged) when 

removing old switch to Black dimmer lead.

•  First Traveler wall box wire to Red dimmer lead 

(note wire color).

•  Remove Red insulating label from Yellow/Red dimmer lead.

•  Second Traveler wall box wire to Yellow/Red dimmer lead 

wire color). This traveler from the dimmer must go to the terminal 

screw on the remote marked "YL/RD".

•  Line Neutral wall box wire to White dimmer lead.

NOTE: "BK" and "RD" terminals on coordinating remote are unused.  

Tighten both screws.

NOTE: Maximum wire length from dimmer to last remote is 

300 ft (90 m).

•  Green or bare copper wire in wall box to Green terminal screw.

•  Load wall box wire identified (tagged) when removing old switch 

to First Traveler 

(note color as above).

•  Second Traveler wall box wire 

(note color as above) to terminal 

screw marked "YL/RD". This traveler from the remote must go to 

the Yellow/Red dimmer lead.

•  Remove White insulating label from terminal screw marked "WH". 

•  Line Neutral wall box wire to terminal screw marked "WH".

• 

NOTE: Use check boxes           when Steps are completed.

Single Pole
1. Line (Hot)

2. Neutral

3. Ground

4. Load 

3-Way
1. Line or Load (see important instruction below)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color. NOTE: For 

matching remote w/LEDs installation, the 

First Traveler becomes Line Hot.

NOTE: You only need to remove side sections if installing with other 

dimmers or if it does not fit in wall box – not when installing with 

mechanical switches.

If installing Dimmer in a single device application, proceed with the 

INSTALLING YOUR DIMMER section. If installing Dimmer in a multi-

device application, proceed as follows:

Your Dimmer includes three color options. The Dimmer ships with the 

White frame attached. To change color of frame, proceed as follows:

OFF POWER at circuit breaker or fuse and test that power 

is off before wiring!

NOTE: If the wiring in your wall box does not resemble any 

of these configurations, consult a qualified electrician.