HIMS International Corporation H432B 用户手册
document, you should press “Enter-w (dots 2-4-5-6)” to activate this
command.
command.
5.2.12 Insert Time
To use this function, press “space-m (dots 1-3-4)” or “F2,” and then
press “enter” on “edit” to enter into the “edit” menu. Move to “insert time”
by pressing “space-4” repeatedly. Then, press “enter” on “insert time,” or
press “t (dots 2-3-4-5)” (which is the short cut) in the “edit” menu. Then,
you can insert the current time where the cursor is located. While you
are editing a document, press “backspace-w (dots 2-4-5-6)” to activate
this function.
press “enter” on “edit” to enter into the “edit” menu. Move to “insert time”
by pressing “space-4” repeatedly. Then, press “enter” on “insert time,” or
press “t (dots 2-3-4-5)” (which is the short cut) in the “edit” menu. Then,
you can insert the current time where the cursor is located. While you
are editing a document, press “backspace-w (dots 2-4-5-6)” to activate
this function.
5.2.13 Changing Between Insert and Overwrite Mode
There are two ways of editing documents in the Braille Sense U2. The
first is to insert your text, which will push back the words behind the
cursor. This is called the “Insert mode” because you are simply inserting
text. When you are in “Insert mode,” the cursor will show up “dots 7-8.”
The second is to overwrite text at the cursor location. This is called the
“Overwrite mode.” In “Overwrite mode”, the cursor will display as blinking
“dots 7-8.”
first is to insert your text, which will push back the words behind the
cursor. This is called the “Insert mode” because you are simply inserting
text. When you are in “Insert mode,” the cursor will show up “dots 7-8.”
The second is to overwrite text at the cursor location. This is called the
“Overwrite mode.” In “Overwrite mode”, the cursor will display as blinking
“dots 7-8.”
If you start the word processor (or open a document), the “Insert mode”
is the default. This will write text, while pushing back other words that
are already in the document. However, you can overwrite text while
erasing the old text by switching to “Overwrite mode.” You can switch to
the “Overwrite mode” by pressing “Space-i (dots 2-4).” In the “Overwrite
mode,” you can change the old text into new text at the cursor location. If
you want to go back to “Insert mode,” you should press “Space-i (dots 2-
4)” again. You can also access this function via the menu. Press “Space-
m (dots 1-3-4)” or “F2,” and go to “Edit” using the up and down arrows
(“Space-1” and “Space-4”). Next, press “Enter” on “Edit” to enter in to the
“Edit” menu. Then, use the scroll buttons to scroll to find “Toggle
Insert/Overwrite Mode,” or you can just press “m (dots 1-3-4)” while you
are in the “Edit” menu.
is the default. This will write text, while pushing back other words that
are already in the document. However, you can overwrite text while
erasing the old text by switching to “Overwrite mode.” You can switch to
the “Overwrite mode” by pressing “Space-i (dots 2-4).” In the “Overwrite
mode,” you can change the old text into new text at the cursor location. If
you want to go back to “Insert mode,” you should press “Space-i (dots 2-
4)” again. You can also access this function via the menu. Press “Space-
m (dots 1-3-4)” or “F2,” and go to “Edit” using the up and down arrows
(“Space-1” and “Space-4”). Next, press “Enter” on “Edit” to enter in to the
“Edit” menu. Then, use the scroll buttons to scroll to find “Toggle
Insert/Overwrite Mode,” or you can just press “m (dots 1-3-4)” while you
are in the “Edit” menu.