Antonio Precise Products Manufactory Ltd. 0160609 用户手册
Introduction
2
Package Contents
2
Charging method
2
Appearance
3
Operations
4
Important Information
6
Warranty
7
This User's Guide is published by ATO without any warranty. Improvements and changes to this
User's Guide necessitated by typographical errors, inaccuracies of current information ,or
improvements to programs and /or equipment, may be made by ATO at any time and without notice.
The Bluetooth trademarks are owned by Bluetooth SIG, Inc.USA.
Thank you for purchasing BT95 by ATA. BT95 is a complete
Bluetooth Stereo Headset that provides Headset, Handsfree
and Audio Streaming which is compliant with Bluetooth
specification v1.2. BT95 profiles supported: Headset,
Handsfree, A2DP, and AVRCP.
BT95 Bluetooth Stereo Headset
USB changing cable
User's Manual
Table of contents
Introduction
Package Contents
Appearance
Front view
BT95 - foldable headband
for easy storage
LED indicator
Ear clip
Rotary mic.
ON/OFF button
Vol. button
Charging
jack
jack
2
3
4
Stereo Headset BT95
User's Manual
Scenario 1: Bluetooth headset and Bluetooth dongle
(a) Pairing
1) Press and hold the ON/OFF button about 5 sec. until the
1) Press and hold the ON/OFF button about 5 sec. until the
LEDs (Blue and Red color) are flashing in 0.5s interval.
2) The LED (Blue color) will flash in 1.5s interval if pairing is succeed.
3) Press and hold the ON/OFF button about 5 sec. until the LED
(Blue color) turns off.
(b) Button operation while playing music (A2DP)
Button
Description
ON/OFF
Short Press (around 1sec.) - turn ON
Long Press (around 5sec.) - turn OFF
VOL +
Volume up
VOL -
Volume down
(c) Button operation during phone call (Handsfree)
Button
Description
ON/OFF
Short Press (around 1sec.) - turn ON
Long Press (around 5sec.) - turn OFF
VOL +
Volume up
VOL -
Volume down
Scenario 2: Bluetooth headset and Bluetooth mobile
(a) Pairing and connection
1) Activate the Bluetooth functions on the mobile phone.
1) Activate the Bluetooth functions on the mobile phone.
2) Search for the Bluetooth stereo headset device (BT95).
3) Press and hold (about 5 sec.) the ON/OFF button of the stereo
headset (BT95) until the LEDs (Blue and Red color) is flashing in
0.5s time interval
4) Select the name of the stereo headset from the device list showing
Bluetooth devices which in discoverable mode within the range.
5) Enter the PIN "0000" to request pairing.
6) The LED (Blue color) will flash in 1.5s time interval. In the case,
the Headset profile should be connected (but no A2DP profile).
7) Connect A2DP profile from the mobile. Please refer to the
operations stated in the user's manual of the mobile phone.
(For example: open the music player program in the mobile phone
and play the music via headset.)
(b) Button operation while playing music (A2DP)
Button
Description
ON/OFF Play or Pause muisc, turn ON/OFF
VOL +
Volume up
VOL -
Volume down
(c) Button operation during phone call (Handsfree)
Button Description
ON/OFF Short press
(around 1 sec.)
-pick up call
(call active state)
Short press
(around 1 sec.)
-hang up call / release
active accpet other call
(call active state)
Long press
(around 2 sec.)
-call transfer to the mobile
phone / hold active accept other call
(call active state)
Long press
(around 2 sec.)
-reject call
(incoming call state)
Double click - mic mute
(call active state)
Short press
(around 1 sec.)
- turn ON
Long press
(around 5 sec.)
- turn OFF
(any state)
VOL +
Volume up
VOL -
Volume down
Remarks:
1) When the headset and dongle are paired the end user is required to press
both
ON/OFF button for 1 sec. then both devices will be connected
again automatically.
2) Don't use Linear AC-DC adaptor but use Switching AC-DC adaptor (5.5v) or USB jack.
3
4) This equipment is to be supplied from an identitied USB port complying with the
requirements of Limited Power Source.
) Fixed PIN code: 0000
Please read all this information before using BT95
1. Please note that only the ATA authorized dealer or service
partner should remove and/or replace the unit, or any other
components.
2. Please use ATA original accessories only. Use of non-ATA
original accessories may result in damage, loss of per-
formance to the product, injury, electric shock or even fire.
3. Please do not expose the product to extreme high or low
temperatures, moisture or fluid.
4. Please do not drop, throw or bend the product as rough
treatment will damage it.
5. Some medical electronic equipment may not be shielded
from RF energy. Therefore, please do not use the headset
near medical equipment without permission.
6. Please turn off the unit before boarding any aircraft.
To prevent any interference with communication systems,
please do not use the unit while the plane is in the air.
7.Please do not allow children to play with the unit
since it contains small parts.
Thank you for purchasing BT95 Bluetooth stereo headset. Within
the warranty period, if the product fails to operate under normal
use and service, due to improper workmanship or material, the
authorized dealers will, at their option, either replace or repair the
product in accordance with the following terms and conditions:
1. The warrnaty is valid only if the original receipt issued to the
1. The warrnaty is valid only if the original receipt issued to the
original purchase by ATA authorized dealer is presented with the
product to be replaced or repaired. The date of purchase and
serial number shall be specified in receipt. For the replacement
and repair policies and procedures in the countries / provinces
which the product is purchased, please refer to the local ATA
authorized dealer.
2. The warranty does not cover any failure of product due to
2. The warranty does not cover any failure of product due to
normal tear and wear, or misuses, including but not limit to use in
other than the manner according to the instructions for operation
and maintenance of the product. The warranty also does not cover
any failure of the product due to modification, adjustment,
accident, acts of God, or any improper use or storage.
3. The warranty does not cover product failure due to improper
3. The warranty does not cover product failure due to improper
repair, modification, adjustment, installation, or service by a non
authorized ATA services partner.
4. The warranty does not cover product failures caused by the use
4. The warranty does not cover product failures caused by the use
of non ATA original accessories.
5. ATA shall not be liable for any losses, damages whatsoever,
5. ATA shall not be liable for any losses, damages whatsoever,
including but not limit to any lost of profits, damage to property,
personal injury and death, arising under or related to the use of the
product and/or the accompanying software, written material or
from errors, deficiencies or fault, whether such loss or damage is
caused by negligence or otherwise.
6. The warranty terms and conditions will be subject to change
6. The warranty terms and conditions will be subject to change
without prior notice.
Operations
Operations
Important Information
Warranty
5
6
7
8
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Statement
Charging method
Use the USB charging cable or AC/DC switching adaptor
connect to BT95 charging jack. When the BT95 in the charging
mode, the LED will be change to red colour. When the battery
of BT95 was fully charging , the LED will be turn off
automatically.
Note : It will take 4 hours to fully charge the headphones.