Honeywell International Inc. EDA510 用户手册

1.  Open the USB cover at the bottom of ScanPal™ terminal; 

2.  Connect ScanPal™ terminal to the power adapter with USB charging cable; 

3.  Make sure the replaceable adapter plug plugged into the power adapter; 

4.  Connect the power adapter to the wall plug and start charging for ScanPal™ 

terminal.

1.  Tap All Apps > Demos > Scan Demo; 

2.  Click Scan on the screen or press one of the Scan Buttons; 

3.  Center the aiming beam over the barcode; 

4.  Adjust the aiming beam: for optimum performance, avoid reflections by 

scanning the barcode at a slight angle. Scan the barcode to slowly move the 

aiming beam over the bar code;

5.  The information is obtained when the barcode is successfully decoded and the 

terminal beeps.

Remarks: 

It's recommended to use Honeywell's peripherals, batteries, USB charging cables 

and power adapters. 

Damages caused by using non-Honeywell peripherals, batteries, USB charging 

cables or power adapters are not covered by the warranty. 

Warnings: 

Please make sure all kits are dry when use the terminal and battery with other 

accessories. 

Damages caused by using wet kits may not be covered by the warranty.

1.  Press the power button and then release (less than 2 seconds) 

2.  To wake up the device from sleep mode, press the power button and then 

release (less than 2 seconds) 

When something is wrong with the OS, press the reset button and then release to 

restart ScanPal™ terminal 

The status of power indicators in non-charging and charging process are 

illustrated as below:

1. Power off; 

2.  Press down the battery cover safety button to move the lock to the unlock 

position at right; 

3.  Open the battery cover with the battery cover buckle handle ; 

4.  Pull out the battery (First open the battery connector side, then pull out the 

battery) 

5.  Insert the Micro SD card to SD card slot until it clicks; 

6.  Insert the battery (Insert the non-connector side first, then press the battery 

down to establish connection between the battery and the phone); 

7.  Press down the battery cover (Insert the non-connector side first, then press the 

battery cover down); 

8.  Press down the battery cover safety button to move the battery cover safety lock 

to the lock position at left; 

9. Power on

The smaller the barcodes, the closer the aiming beams should get to the 

barcodes 

The bigger the barcodes, the father the aiming beams should get to the 

barcodes 

For information about technical support, after-sales service and maintenance, 

please visit www.honeywellaidc.com. 

For the local version of this article, please visit www.honeywellaidc.com. 

For information on patents, please refer to www.honeywellaidc.com/patents. 

Please log into www.honeywellaidc.com/warranty_information for warranty 

information on your product. 

Honeywell International Inc. reserves the rights to modify the specifications and 

other information mentioned above without prior notification. Readers should 

consult Honeywell International Inc. to make sure if any changes made any time 

they read this article. The information in this article does not represent any 

commitments of Honeywell International Inc. 

Honeywell International Inc. is not responsible for direct or indirect loss caused by 

any technical or editing errors or omissions contained in this article. 

The proprietary information contained in this article is protected by copyright. All 

rights reserved. Without prior written consent from Honeywell International Inc., 

any form of photocopy, copy or translation into other languages for any part of 

this article is not allowed.

1.  Power off the device; 

2.  Press down the battery cover safety button and move the battery cover lock to 

the unlock position to the right; 

3.  Open the battery cover using the battery cover notches; 

4.  Pull out the battery: first pull the bottom side, then pull out the battery; 

5.  Insert the SIM card into the SIM card slot until it clicks; 

6.  Insert the battery: insert the top part first, then press the bottom part to lock it in 

place; 

7.  Install the battery cover: insert the bottom part first, then press the top part; 

8.  Press down the battery cover safety button and move the battery cover lock to 

the lock position at the left; 

9.  Power on the device

1.  Only EDA51-1 delivers this feature

2.  It's recommended to use standard Nano SIM card. Using non-standard Nano 

SIM card may cause the network unusable and even damage the card and 

slot;

3.  Damages caused by using non- standard Nano SIM card are not covered by 

the warranty.

Replaceable adapter plug

Power 
adapter

Micro USB 
cable

USB Cover

Scan Engine

During charging process, and the 

charging is about to be completed

During charging process, and the battery 

power is still low

Off

Battery power is normal

Flashing orange

Battery power is low

Constant green

Charging complete

Flashing green

Orange

Flashing red

Battery is abnormal

Micro SD

Nano SIM Card

© 2018 by Honeywell International Inc. All rights reserved.

Website: www.honeywellaidc.com

Micro SD