Murata Electronics North America DNT500FP 用户手册
www.RFM.com
Technical support +1.800.704.6079
Page 24 of 58
©2008 by RF Monolithics, Inc.
E-mail: tech sup@rfm.com
DNT900 - 11/05/08
3.5 Interfacing to 5 V Logic Systems
All logic signals including the serial ports on the DNT500 are 3.3 V signals. To interface to 5 V signals, the
resistor divider network shown below must be placed between the 5 V signal outputs and the DNT500
signal inputs. The output voltage swing of the DNT500 3.3 V signals is sufficient to drive 5 V logic inputs.
resistor divider network shown below must be placed between the 5 V signal outputs and the DNT500
signal inputs. The output voltage swing of the DNT500 3.3 V signals is sufficient to drive 5 V logic inputs.
5V
Logic
DNT500
2.2K
4.3K
Figure 3.5.1
3.6 Power-On Reset Requirements
The DNT500 has an internal reset circuit that generates and maintains the DNT500 in a reset state until
the power supply voltage reaches 3.3 volts for 100 milliseconds. This reset circuit protects the radio and
non-volatile memory from brown-out voltage conditions. If devices that communicate with the DNT500
have shorter reset periods, an allowance must be made to allow the DNT500 to come out of reset. Com-
mands and data sent before the DNT500 is out of reset will be ignored.
the power supply voltage reaches 3.3 volts for 100 milliseconds. This reset circuit protects the radio and
non-volatile memory from brown-out voltage conditions. If devices that communicate with the DNT500
have shorter reset periods, an allowance must be made to allow the DNT500 to come out of reset. Com-
mands and data sent before the DNT500 is out of reset will be ignored.
3.7 Mounting and Enclosures
DNT500C radio modules are mounted by reflow soldering them to a host circuit board. DNT500P mod-
ules are mounted by plugging their pins into a set of mating connectors on the host circuit board. Refer to
the DNT500 Data Sheet for DNT500P connector details.
ules are mounted by plugging their pins into a set of mating connectors on the host circuit board. Refer to
the DNT500 Data Sheet for DNT500P connector details.
DNT500 radio module enclosures must be made of plastics or other materials with low RF attenuation to
avoid compromising antenna performance. Metal enclosures are not suitable as they will block antenna
radiation and reception. Outdoor enclosures must be water tight, such as a NEMA 4X enclosure.
avoid compromising antenna performance. Metal enclosures are not suitable as they will block antenna
radiation and reception. Outdoor enclosures must be water tight, such as a NEMA 4X enclosure.
3.8 Connecting Antennas
A U.FL miniature coaxial connector is provided on both DNT500 configurations for connection to the
RFIO port. A short U.FL coaxial cable can be used to connect the RFIO port directly to an antenna. In this
case the antenna should be mounted firmly to avoid stressing the U.FL coaxial cable due to antenna
mounting flexure. Alternately, a U.FL coaxial jumper cable can be used to connect the DNT500 module to
RFIO port. A short U.FL coaxial cable can be used to connect the RFIO port directly to an antenna. In this
case the antenna should be mounted firmly to avoid stressing the U.FL coaxial cable due to antenna
mounting flexure. Alternately, a U.FL coaxial jumper cable can be used to connect the DNT500 module to
a U.FL connector on the host circuit board. The connection between the host circuit board U.FL connector
and the antenna or antenna connector on the host circuit board should be implemented as a 50 ohm
stripline. The design details of the stripline are covered in the DNT500 Data Sheet.
and the antenna or antenna connector on the host circuit board should be implemented as a 50 ohm
stripline. The design details of the stripline are covered in the DNT500 Data Sheet.