Zebra Technologies Corporation MD-BTC2TY6 用户手册
Installing the Battery
Batteries are shipped uncharged. Remove any protective packaging from new battery packs, install it
in the printer and charge completely prior to initial use.
Important Safety Information
Static Discharge and Thermal Printing
Caution • Static Discharge
The discharge of electrostatic energy can damage or destroy the printhead or electronic
components used in this device. DO NOT TOUCH the printhead or any exposed electronic
components.
Caution • Printhead
The printhead can become hot after prolonged printing. Use only the supplied cleaning pen
to perform maintenance on the printhead.
Battery Safety
Always observe the safety precaution in the Lithium-Ion Battery Technical Bulletin included with
each Battery Pack.
Caution • Short Circuits
Avoid accidental short circuiting of any battery. Allowing battery terminals to contact conduc-
tive material will create a short circuit which could cause burns and other injuries or could start
a fire.
Important • Lithium-Ion (Li-ion) Battery Disposal
Always dispose of used printer batteries properly. Disposal regulations may vary by loca-
Always dispose of used printer batteries properly. Disposal regulations may vary by loca-
tion. Refer to the MZ series Users Guide for more battery recycling information.
Caution • Use Zebra Chargers
Use of any charger not approved specifically by Zebra for use with its batteries could cause dam-
age to the Battery Pack or the Printer and will void the warranty.
Product Support
For product support, contact Zebra Technologies at:
www.zebra.com
In the Americas contact:
Zebra Technologies International, LLC
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061-3109 USA
Phone: +1.847.793.2600 or +1.800.423.
0422
Fax: +1.847.913.8766
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061-3109 USA
Phone: +1.847.793.2600 or +1.800.423.
0422
Fax: +1.847.913.8766
In Europe, Africa, the Middle East, and India
contact
Zebra Technologies Europe Limited
Zebra House
The Valley Centre, Gordon Road
High Wycombe
Buckinghamshire HP13 6EQ, UK
Phone: +44.1494.472872
Fax: +44.1494.450103
The Valley Centre, Gordon Road
High Wycombe
Buckinghamshire HP13 6EQ, UK
Phone: +44.1494.472872
Fax: +44.1494.450103
In the Asia Pacific region contact:
Zebra Technologies Asia Pacific, LLC
16 New Industrial Road
#05-03 Hudson TechnoCentre
Singapore 536204
Phone: +65-6858 0722
Fax: +65-6885 0838
MZ 220
MZ 320
1. Feed Switch
2. Media Status Light
3. USB Port
4. Battery Charging Receptacle
5. Media Sensor
6. Media Cover
7. Platen
8. Printhead
9. Latch Release Button
10. Communications Status Indicator
11. IR window
12. Charge Status Indicator
13. Power Switch
14. Power Indicator
15. Belt Clip
16. Battery Door Latch
17. Battery Compartment Cover
18. Battery Pack
19. External Charge Contacts
11. IR window
12. Charge Status Indicator
13. Power Switch
14. Power Indicator
15. Belt Clip
16. Battery Door Latch
17. Battery Compartment Cover
18. Battery Pack
19. External Charge Contacts
Charging the Battery
Printer Controls
Loading Media
Introduction
Thank you for choosing one of our Zebra MZ Series Mobile Printers.
These rugged printers will become productive and efficient additions to
your workplace thanks to their innovative design. Because they are made
by Zebra Technologies Corporation, you can be assured of world-class
support for all of your bar code printers, software, and supplies.
your workplace thanks to their innovative design. Because they are made
by Zebra Technologies Corporation, you can be assured of world-class
support for all of your bar code printers, software, and supplies.
This document provides an easy reference for operating and
maintaining the MZ Series Mobile Printers. Complete documentation for
this printer series is provided by the
this printer series is provided by the
MZ Series User Guide available on
the Internet at:
http://www.zebra.com.
MZ Series Overview
(MZ 220 Illustrated)
Load the Media Roll
Close the Cover
Zebra
®
MZ Series
Mobile Printers
Quick Start Guide
QSG-MZS-002 rev. A
© ZIH Corp. 2006
Over
The printer may be used while charging the battery. However, prolonged use of the printer
while charging will greatly increase charge times.
Using the Charger Power Supply
15
16
7
1
2
4
6
3
8
18
17
9
Power Button
Press to turn unit on.
Press again to turn unit off
Feed Button
Press to advance the media a
software determined length of
journal media.
software determined length of
journal media.
Communication Light (Blue)
When lit steadily indicates a wireless
communications link is established, when
blinking indicates data transmission.
communications link is established, when
blinking indicates data transmission.
Charge Light (Green/
Amber)
Green indicates the battery
fully charged. Amber indicates
the battery is less than 90%
charged.
IrDA Window
This area must be within the line of sight
of any other IrDA enabled device for IR
communications to occur.
Media Status Light
(Amber)
When off Indicates normal operation,
blinking indicates either no media or
that the media compartment is open
blinking indicates either no media or
that the media compartment is open
Power Light (Green)
Indicates power status and battery condition. A
steadily lit indicator means the battery has more
than a 30% charge remaining. A blinking indicator
means the battery has less than a 30% charge
remaining.
steadily lit indicator means the battery has more
than a 30% charge remaining. A blinking indicator
means the battery has less than a 30% charge
remaining.
10
11
12
13
14
19
1. Use a coin to rotate the
Battery Compartment
lock
Battery Compartment
lock
1
/
4
turn as shown.
2. Remove the Battery
Compartment Cover
Compartment Cover
3. Plug the Battery
Pack connector into the
Printer.
Pack connector into the
Printer.
Battery Pack
Note location of label
Note location of label
4. Re-install the Battery Compartment Cover and rotate
the lock back
the lock back
1
/
4
turn to lock it in place .
Ensure battery leads are not pinched prior to replacing
battery cover.
Charger Power Supply
Plug into AC receptacle
Plug into printer Charger Jack
Verify that the mains adapter shipped
with your Printer is the correct one for
your region.
Install the mains adapter into the
Power Supply by hooking the top edge
into the mains receptacle cavity, and
rotating it until it snaps into place.
with your Printer is the correct one for
your region.
Install the mains adapter into the
Power Supply by hooking the top edge
into the mains receptacle cavity, and
rotating it until it snaps into place.
Preparing the Charger Power Supply
Remove the power supply from its box. Remove and discard
the shipping ring from the mains receptacle cavity.
the shipping ring from the mains receptacle cavity.
Mains Adapter
Shipping Ring
Remove and discard
Remove and discard
5
Media Roll
Note direction media pulls
off the roll.
Note direction media pulls
off the roll.
Pull Media out of Printer
Close Media Cover
Press Latch
Button
Button
Media Cover Opens
Open the Media Cover
QSG-MZS-001 rev. A
© ZIH Corp. 2006