ZyXEL Communications Corporation VMG1312T10C 用户手册
Chapter 9 Quality of Service (QoS)
VMG1312-T10C User’s Guide
126
Service
Select the service classification of the traffic (FTP or SIP).
IP Protocol
Select this option and select the protocol (service type) from TCP or UDP. If you select
User defined, enter the protocol (service type) number.
User defined, enter the protocol (service type) number.
TCP ACK
If you select this option, the matched TCP packets must contain the ACK (Acknowledge)
flag.
flag.
DHCP
Select this option and select a DHCP option.
If you select Vendor Class ID (DHCP Option 60), enter the Class ID of the matched
traffic, such as the type of the hardware or firmware.
traffic, such as the type of the hardware or firmware.
If you select ClientID (DHCP Option 61), enter the Type of the matched traffic and
Client ID of the DHCP client.
Client ID of the DHCP client.
If you select User Class ID (DHCP Option 77), enter the User Class Data, which is
a string that identifies the user’s category or application type in the matched DHCP
packets.
a string that identifies the user’s category or application type in the matched DHCP
packets.
If you select VendorSpecificIntro (DHCP Option 125), enter the Enterprise
Number of the software of the matched traffic and Vendor Class Data used by all the
DHCP clients.
Number of the software of the matched traffic and Vendor Class Data used by all the
DHCP clients.
Packet Length
This field is available only when you select IPv4 (0x0800) in the Ether Type field.
Select this option and enter the minimum and maximum packet length (from 46 to
1504) in the fields provided.
1504) in the fields provided.
IPP/DS Field
Select IPP/TOS to specify an IP precedence range and type of services.
Select DSCP to specify a DiffServ Code Point (DSCP) range.
IP Precedence
Range
Enter a range from 0 to 7 for IP precedence. 0 is the lowest priority and 7 is the
highest.
highest.
Type of Service
Select a type of service from the drop-down list box.
DSCP Range (0
~ 63)
Select this option and specify a DSCP (DiffServ Code Point) number between 0 and 63
in the field provided.
in the field provided.
802.1P
Select this option and select a priority level (between 0 and 7) from the drop-down list
box.
box.
"0" is the lowest priority level and "7" is the highest.
VLAN ID
Select this option and enter the source VLAN ID in this field.
Exclude
Select this option to exclude the packets that match the specified criteria from this
classifier.
classifier.
Action
Forward To
Select the interface through which traffic that matches the rule is forwarded out. If you
select Unchange, the Device forwards traffic of this class according to the default
routing table.
select Unchange, the Device forwards traffic of this class according to the default
routing table.
If traffic of this class comes from a WAN interface and is in a queue that forwards traffic
through the LAN/WLAN interface, the Device ignores the setting here.
through the LAN/WLAN interface, the Device ignores the setting here.
IPP/DS Field
Select IPP/TOS to specify an IP precedence range and type of services.
Select DSCP to specify a DiffServ Code Point (DSCP) range.
IP Precedence
Mark
Enter a range from 0 to 7 to re-assign IP precedence to matched traffic. 0 is the lowest
priority and 7 is the highest.
priority and 7 is the highest.
Type Of Service
Mark
Select a type of service to re-assign the priority level to matched traffic.
Available options are: Normal service, Minimize delay, Maximize throughput,
Maximize reliability and Minimize monetary cost.
Maximize reliability and Minimize monetary cost.
Table 43
Class Setup: Add/Edit (continued)
LABEL
DESCRIPTION