Xmark Corporation MAR 用户手册
Installing the Locator
The steps below correspond to the numbers in Figure 2.
1
Remove the Mounting Plate from the Locator.
2
Charge the Locator batteries.
The Locator contains rechargeable lithium-ion batteries. Plug the
supplied AC adapter into a 120 VAC outlet, and then connect
it to the Locator. The CHARGING light will come on. A full
charge takes approximately 3 hours.
it to the Locator. The CHARGING light will come on. A full
charge takes approximately 3 hours.
3
Attach the two antennas.
The antennas use a BNC connector. Push the antenna onto the
mast, and give it a ¼ turn clockwise to secure it.
Note: The antennas have a protective covering to prevent them
from touching metal. Do not encase, wrap, or otherwise cover
the antennas.
from touching metal. Do not encase, wrap, or otherwise cover
the antennas.
4
Install the mounting plate using one of the following methods.
A
Fasten to the stand using the three screws supplied.
B
Install to a vertical surface using mounting hardware appro-
priate to the surface material, such as screws, double-sided
tape or cable ties.
tape or cable ties.
5
Install the Locator to the mounting plate.
Slide the Locator into the mounting plate. If desired, the Locator
can be secured by inserting a small lock or cable tie through the
top hole on the mounting plate and Locator.
can be secured by inserting a small lock or cable tie through the
top hole on the mounting plate and Locator.
Installation is complete, and the Locator is now ready for use.
Gathering Asset Data
The Locator can gather data on assets in your facility carrying FindIt
tags either on its own, or when connected to a Client PC with the
FindIt software.
tags either on its own, or when connected to a Client PC with the
FindIt software.
Refer to the FindIt Portable User Manual for detailed informa-
tion on how to gather data.
tion on how to gather data.
Charging the Batteries
The STATUS light on the Locator begins to fl ash when the batteries
require recharging. The Locator will continue to receive FindIt tag
transmissions for a further 20-30 minutes, and will then shut down.
All data received up to that time are saved.
require recharging. The Locator will continue to receive FindIt tag
transmissions for a further 20-30 minutes, and will then shut down.
All data received up to that time are saved.
Plug the Locator into a 120 VAC outlet using the supplied AC
adapter. The CHARGING light will remain on until the charge is
complete. A full charge takes 3 hours, providing approximately 24
hours of operation.
adapter. The CHARGING light will remain on until the charge is
complete. A full charge takes 3 hours, providing approximately 24
hours of operation.
The Locator should be charged every few months when not in use
to maximize battery life.
to maximize battery life.
Warning: Only charge the Locator using the supplied adapter. Failure
to do so may cause the battery to become hot, explode or ignite and
cause serious injury.
to do so may cause the battery to become hot, explode or ignite and
cause serious injury.
STATUS and CHARGING Lights
The locator has a STATUS light and CHARGING light, which
provide basic information about the Locator’s operation. Both lights
are located on the left side of the Locator.
provide basic information about the Locator’s operation. Both lights
are located on the left side of the Locator.
Battery Handling
This device contains lithium-ion batteries. Do not place the batteries
in or near fi re, or in direct sunlight. Heating the batteries can damage
the safety circuitry, which can cause additional heating, rupture or
ignition of the batteries.
in or near fi re, or in direct sunlight. Heating the batteries can damage
the safety circuitry, which can cause additional heating, rupture or
ignition of the batteries.
The batteries are not user replaceable. Never open the case on
the Locator.
the Locator.
Installing the Locator
Gathering Asset Data
Battery Handling
Charging the Batteries
STATUS Light (Green)
Off
Not receiving tag messages, or batteries are
fully discharged.
fully discharged.
Occasional fl ashes
Locator is receiving tag messages.
Steady fl ashes
Batteries are low. Recharge immediately. The
Locator will continue to receive tag messages
for a further 20-30 minutes, and will then shut
down. (All data are saved).
Locator will continue to receive tag messages
for a further 20-30 minutes, and will then shut
down. (All data are saved).
On
Error. Connect to the Client PC to automatically
download fi rmware.
download fi rmware.
CHARGING Light (Red)
On
Batteries are charging
Off
Batteries are fully charged.
STATUS and CHARGING Lights