Martec Access Products Inc TTI-10T 用户手册

A - Key hole (trou piriforme, bocallave)

B - Pencil (crayon, lápiz)

C - Screwdriver (tournevis, destornillador)

D - Top screw (vis supérieure, tornillo superior)

To reduce the risk of injury, do not attempt to use this product until you have 
read thoroughly and understand completely this operator’s manual and the 
operator’s manual for the GD200 garage door opener. Ensure compatibility 
and fit before using this accessory. Do not use this accessory if a part is 
damaged or missing.



Install keypad in sight of garage door and at least five feet above the floor.



Always keep the moving door in sight and away from people and objects until 
it is completely closed. No one should cross the path of the moving door.



Do not allow to be used as a toy. Close attention is necessary when used by 
children.



Save these instructions. Refer to them frequently and use them to instruct 
others who may use this product. 

This product may contain chemicals, including lead, known to the State of 
California to cause cancer, birth defects or other reproductive harm. 

Outdoor Keypad, 9 Volt Battery, Operator’s Manual

The following signal words and meanings are intended to explain the levels 
of risk associated with this product.

Indicates an imminently hazardous situation, which, 
if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation, which, if 
not avoided, could result in death or serious injury.

The following signal words and meanings are intended to explain the levels 
of risk associated with this product.

Indicates a potentially hazardous situation, which, if 
not avoided, may result in minor or moderate injury. 

(Without Safety Alert Symbol) Indicates important 
information not related to an injury hazard, such as a 
situation that may result in property damage.

Some of the following symbols may be used on this product. Please study 
them and learn their meaning. Proper interpretation of these symbols will allow 
you to operate the product better and safer.

Safety Alert

Indicates a potential personal injury hazard.

Read 
Operator’s 
Manual

To reduce the risk of injury, user must read and 
understand operator’s manual before using 
this product.

Moving Door

To avoid death or serious personal injury, stay 
clear of the garage door while it is moving and 
never attempt to run or walk under moving 
garage door.

Do not use garage door opener if keypad does not start and stop the motor. 
An opener that cannot be controlled with a keypad is dangerous, can result 
in death or serious personal injury, and must be repaired. 

Make sure the keypad is mounted high enough to prevent unauthorized 
activation of the garage door opener. It should be placed at least 5 feet above 
the floor so that it is inaccessible to children. Unauthorized activation of the 
opener can result in death or serious personal injury. 

Do not start or stop the garage door opener if there is a person or object 
in the path of the door, the door has not been properly balanced, or if you 
cannot see the doorway. Failure to follow these instructions can result in 
death or serious personal injury.

Only install screws, bolts, anchors, and other hardware into sound structural 
supports in areas where no electrical wires, utility cables, pipes, or other 
obstructions are located. Failure to follow these instructions can result in 
death, electrical shock, or other serious personal injury.

NOTE: For convenience, we recommend you program the outdoor keypad before 
installing. See 

Programming the Outdoor Keypad for instructions.



Find desired location outdoors and in sight of the garage door. 

 

NOTE: The keypad should be at least 5 feet above the floor so it is 
inaccessible to children.



Use a pencil to mark screw hole placement and install top screw.



Place the wide portion of the key hole over the head of the top screw.



Slide the keypad down until the top screw is inside the narrow portion of the 
key hole.



Remove the battery cover.



Use a level to be sure the keypad is in a vertical position, then install bottom 
screw into the screw hole.

991000836
2-11-16 (REV:01)

A - Battery cover (couvercle du logement de pile, tapa del compartimiento para 

la batería)

B - Battery (pile, batería)

C - Bottom screw (vis inférieure, tornillo inferior)

D - Screw hole (trou de vis, orificio para el tornillo)



Install 9-volt battery.



Replace battery cover.

See Figures 3 - 4.


If you haven’t already done so, install a 9-volt battery into the outdoor keypad. 



Press and hold the 

1 button, then press the ON/PROGRAM button. The 

LEDs on the keypad will flash two times.



Enter your desired PIN (4 digits). The LEDs on the keypad will flash three 
times. This indicates the PIN has been accepted and the keypad is ready to 
be paired with your garage door opener.



Press and hold the 

PROGRAM button on the garage door opener’s console 

until the garage door opener’s LED lights turn off and the light behind the 

PROGRAM button on the console flashes three times. This indicates the 
console is in programming mode.



Press the 

ON/PROGRAM button on the outdoor keypad, then enter your 

PIN. The light behind the 

PROGRAM button on the garage door opener’s 

console will flash three times, then the garage door opener’s LED lights will 
turn on.



Within 30 seconds, press the 

0 button on the keypad to verify the door moves. 

Once it does, the set-up is complete.



To operate the garage door opener after initial set-up, press the 

PROGRAM button on the keypad, then enter your PIN.

NOTE: In order to change the PIN or reset a forgotten PIN, repeat all of the 
steps listed in this section, including syncing the outdoor keypad to the garage 
door opener.

See Figure 4.
It is possible to set up a temporary PIN for use by visitors or service personnel. 
This PIN will remain available only until the next time you enter your regular PIN 
on the keypad.
To set up a temporary PIN:


Press and hold the 

3 button, then press the ON/PROGRAM button. The 

LEDs on the keypad will flash three times.



Enter your current PIN. The LEDs on the keypad will briefly flash twice. 



Enter the desired temporary PIN. The LEDs on the keypad will briefly flash 
three times and the temporary PIN is now ready to use.



To operate the garage door opener using the temporary PIN, press the 

PROGRAM button on the keypad, then enter the temporary PIN.

NOTE: Remember that the temporary PIN will be automatically deleted the next 
time your regular PIN is entered on the outdoor keypad. 

A - Garage door opener console (console de l’ouvre-porte de garage, consola 

del sistema de apertura para portón de garaje)

B - PROGRAM button (bouton de PROGRAM, botón PROGRAM)

C - LED lights (ampoules DEL, luces LED) 

Garage door cannot 
be opened or closed 
with keypad

The garage door is 
locked.

P re s s   t h e   L O C K 
button on the indoor 
keypad to unlock the 
door.

The outdoor keypad can be used to open and close the GD200 Garage Door 
Opener. For security, the outdoor keypad allows you to set up a custom four 
digit personal identification (PIN) code.

1428 Pearman Dairy Rd., 

Anderson, SC 29625 

Phone 1-800-525-2579 

États-Unis, USA 

Téléphone 1-800-525-2579  

Teléfono 1-800-525-2579