Lutron Electronics Company Inc 0085 用户手册

Sivoia

QS Wireless

Cellular Shade

Automated shade with wireless (RF) control
Installation and Programming Guide
(please read before installing)

English

Inside mount

Outside mount

8.1

8.4

Start Here
1. Review components
2. Install mounting brackets
3. Install batteries
4. Install the shade in the brackets
5. Removing the shade from the brackets
6. Programming options

Review components

Included:

Batteries not included

Tools required:

Install mounting brackets

Mount the left and right brackets 2 inches in
from each end of the shade.
Note: Mount additional brackets evenly between
the end brackets and clear of the cord lift.

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Install batteries

Refer to the battery holders for proper
battery alignment.

Install the shade in the brackets

Click the shade into place as shown below.

Programming

RadioRA

•

For assignment and programming without RadioRA 2

design and programming software, refer to the
RadioRA 2 setup guide, available at
www.lutron.com/radiora2

•

Otherwise, use the RadioRA 2 Essentials or Inclusive

software to assign and program your cellular shades.

HomeWorks

•

Use the HomeWorks QS design and programming

software to assign and program your cellular shades.

Standalone

•

Proceed to steps 7 and 8 to assign and program your

cellular shades with standalone controls.

7.1

7.2

Assign control:

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Hold “Close” (6 seconds)

Shade LED blinks
for 2 seconds

Set the limits
Note: Shade limits must either be set with a Pico

or with RadioRA2 or Homeworks QS design and
programming software.

8.2

Enter limit setup mode:

Hold “Open” AND “Raise” (3 seconds)

Shade LED blinks for 2 seconds, then
remains on.

8.3

Adjust limits:

Press “Raise” or “Lower”

Shade LED remains on solid green.

Save and exit:

To set the upper limit: Hold “Open” (6 seconds)

To set the lower limit: Hold “Close” (6 seconds)

Shade LED blinks for 2 seconds, then turns off.

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Tap shade button -
shade LED turns on
solid green

Tap shade button - Shade
LED turns on solid green

Troubleshooting

Symptom

Solution

Shade does not go all the
way down

Fabric needs to relax
(close shade for 24
hours then reset the
lower limit)

Reset the lower limit

Shade hangs unevenly

Ensure that fabric is
not pinched in the
mounting brackets

For more information:
www.lutron.com/
technicaldocumentlibrary/
window%20systems%20
warranty.pdf

Contact the Lutron Technical
Support Center at the numbers
provided below or your local
Lutron sales representative
with questions concerning the
installation or operation of the
System or this Warranty, or to
make a warranty claim. Please
provide the exact model number
when calling.

Lutron, the Sunburst logo, Sivoia,
RadioRA, HomeWorks, and Pico
are registered trademarks
of Lutron Electronics Co., Inc.

Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
USA
TEL: 1.610.282.3800
FAX: 1.610.282.3090
Technical Support:
1.800.523.9466 or
1.610.282.6701
Toll Free: 1.888.LUTRON
EMAIL: shadinginfo@lutron.com
WEB: www.lutron.com/
shadingsolutions

Europe Headquarters |
United Kingdom
Lutron EA Ltd
6 Sovereign Close
London, E1W 3JF, UK
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support: +44.
(0)20.7480.6899
FREEPHONE: 0800.282.107

Asian Headquarters |
Singapore
Lutron GL Ltd
15 Hoe Chiang Road
#07-03
Singapore, 089316
TEL: +65.6220.4666
FAX: +65.6220.4333
Technical Support: 800.120.4491

Limited warranty

Number of years from

date of shipment

Percentage of cost of replacement parts

credited by Lutron

Up to 5

100%

More than 5 but
not more than 8

50%

More than 8

Restore factory defaults (optional)

Tap 3 times, hold 3 seconds, tap 3 times.

Shade LED blinks for 2 seconds
after hold, then for 5 seconds
after second triple-tap.

Mounting
brackets

Cellular shade

Mounting
screws

Endcaps

Phillips-head
screwdriver

Cordless drill
(optional)

Removing the shade from
the brackets

Use a flathead screwdriver
to unclip the shade
as shown.

Enter shade setup mode:

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Open

Preset

Assigning controls

LED

Rechargable

batteries

Side view

FCC Information

Note:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio and television reception, which can
be determined by turning the equipment
off and on. The user is encouraged to try to
correct the interference by one or more of
the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the

equipment and receiver.

· Connect the equipment into an outlet on

a circuit different from that to which the
receiver is connected.

· Consult the dealer or an experienced radio/

TV technician for help.

Note:
Changes or modifications not expressly
approved by Lutron Electronics Co. could
void the user’s authority to operate this
equipment.
* This device complies with Part 15 of the

FCC Rules.

Operation is subject to the following two
conditions:
(1) This device may not cause harmful

interference and

(2) This device must accept any

interference received, including
interference that may cause undesired
operation. This Class B digital apparatus
complies with Canadian ICES-003.