Lutron Electronics Company Inc 0095 用户手册

Roller Shade

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299, U.S.A.

09/2013

P/N 045404 Rev. A

Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.

Equal depth 

both sides

A

 2.1  Press-fit an end cap on the open end of the fascia as shown. 

 2.2  Repeat on the other end.

 3.1  Facing the window, tilt the top of the shade assembly 

C

 

away from you and insert its top rear edge into the channel  
in the shade rail 

A

.

 3.2  Push the bottom of the shade toward the window and lock it 

into the shade rail with a “click.”

 1.1   Hold the shade rail 

A

 up to the mounting surface. Approximate 

its final position and use a pencil to mark mounting screw 
locations on the shade rail.*

 1.2  Pre-drill the shade rail 

A

 

at the pencil marks.

 1.3  Fasten the shade rail 

A

, to the mounting surface using the mounting screws provided 

B

 or other appropriate fasteners.

NOTE: The shade rail features 
grooves to help stabilize the point 
of your drill bit.

**NOTE: Depending on the size 
of your shade and the depth of 
your trim, or the roll direction of 
your shade, you may be able 
to mount the shade directly to 
the wall above the trim without 
additional spacing.
In this arrangement, the top 
of the shade rail must be a 
minimum of 4 

1

/

2

 in (114 mm) 

above the top of the trim.

Optional fascia/end caps 

not shown

NOTE: If your shade was ordered with optional fascia, the fascia 
will be factory-attached and wrapped with the shade. Leave the 
wrapping in place during installation for added stability, then remove 
the wrap before installing batteries.

a. Install mounting screws 6-12 in (152-305 mm) from each end of the 

shade rail.

b. Locate the mounting screws so that they drive into studs or solid 

trim. For other surfaces, use appropriate expansion anchors, toggle 
bolts, or other fasteners, (not included).

c. Verify that the mounted 

shade rail is level and 
parallel to the window 
opening.

#2 Phillips Driver Bit

1/8 in (3.2 mm) Drill Bit

Pencil

Level

D-Cell Alkaline Batteries

(6 or 8 depending on shade size)

Power Drill

OPTIONAL

(1) Shade Rail

A

Mounting Screws

B

Serena

®

 Roller 

Shade Assembly

C

(1) Fascia with end caps

D

A

B

A

C

A

A

Spacer blocks 

or board  

(not included)

securely 

mounted to wall 

above trim**

Worldwide Headquarters | USA
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800 • FAX: 1.610.282.3090
Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1
Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutions

Europe Headquarters | United Kingdom
Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK
TEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107

B

B

End Caps

Left end cap 

shown

Left end cap 

installed

Fascia

NOTE: If your shade will be inside-
mounted, both end caps must be 
installed and fully seated before 
proceeding to the next step.

4.5 in

(114 mm)

min.

Wall

Regular

roll

Reverse

roll

Trim