Lutron Electronics Company Inc 0107 用户手册

0301742  Rev A

GrafikTT

1.   

2.   Install in accordance with all national and local electrical codes.

3.   When no “grounding means” exist in wallbox, the NEC

®

 allows dimmer without 

a grounding connection to be installed as a replacement if 1) a nonmetallic, 

noncombustible faceplate is used with nonmetallic attachment screws or 2) the 

circuit is protected by a ground fault circuit interrupter (GFCI). For this type of 

installation, cap or remove the green ground wire on the dimmer, and use an 

appropriate wallplate, such as a Lutron

®

 GrafikT

TM

 series wallplate.

4.

   GrafikT

TM

 dimmers are not compatible with standard 3-way switches. Use only with 

companion dimmers (GT-AD-S or GT-AD).

5.   Companion dimmers (GT-AD-S or GT-AD) cannot be used individually but must be 

used in conjunction with a GrafikT

TM

 dimmer in a multi-location application.

6.   In any multi-location circuit, use only one GrafikT

TM

 dimmer with up to four 

companion dimmers.

7.   GrafikT

TM

 dimmer settings such as Light Bar Intensity and Speaker On/Off can be 

modified using Advanced Programming Mode. For instructions and information on 

how to use Advanced Programming Mode, please visit www.lutron.com/grafikT or 

call Lutron

®

 Technical Support at 1.800.523.9466.

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299

150 W

600 W

—

150 W

250 W

350 W
8 maximum

250W

250 W

250 W

For use with HQRT-25CL and RRT-25CL

For use with all other models

120 V~  60 Hz

:

499485; CR6X-PP2

:

426122(9290002330)(822580)(bc=046677426125)

:

ECO-575L 

:

78390 (LED8R20/DIM/SE/830/RP)

FEIT (Utilitech):

PAR38/LEDG5

For a complete list of compatible LEDs, please visit: 

www.lutron.com/LED

1.800.523.9466      U.S.A. 

|

 Canada 

|

 Caribbean 

+1.888.235.2910   Mexico

+1.610.282.3800   Others 
www.lutron.com

Multi-location - Lights can be dimmed from multiple locations.
One location will be replaced by a GrafikT

TM

 dimmer and the other location(s) by a GrafikT

TM

 

companion dimmer. The dimmer can be wired on the line-side or the load-side.
Dimmer
Connect the 

green ground wire on the dimmer to the green or bare ground wire in the wallbox 

(See 

Important Note 3 at left).

Connect tagged wire removed from the switch to the 

black wire on the dimmer. 

Connect one of the remaining wires removed from switch to the 

red wire on the dimmer.

Connect the remaining wire removed from the switch to the 

blue wire on the dimmer.

Companion Dimmer
Connect the 

green wire on the dimmer to the green or bare ground wire in the wallbox (See 

Important Note 3 at left).
Connect the same color wire connected to the 

red wire on the dimmer to the red wire on the 

companion dimmer, along with the tagged wire.
Connect the remaining wire to the 

blue wire on the companion dimmer.

When combining controls in the same wallbox, derating is required. No derating is 

required for companion dimmers.

1

   Designed for use with permanently installed LED, incandescent, or tungsten halogen only. 

GT-150
GTJ-150

LED

150 W

150 W

150 W

Incand. / Halogen

600 W

500 W

400 W

GT-250M
GTJ-250M
RRT-25CL
HQRT-25CL

LED

250 W

250 W

250 W

Incand. / Halogen

600 W

500 W

400 W

Lutron

®

 Hi-lume

®

 

A-Series LTE LED 

Driver

350 W,  

8 drivers max

350 W,  

8 drivers max

350 W,  

8 drivers max

For warranty details, please visit:  

For FCC/IC information, please visit:  

Lutron is a registered trademark and FASS and GrafikT are trademarks of Lutron Electronics Co., Inc. 
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
© 2014 Lutron Electronics Co., Inc.

Cap the blue wire with the blue connector.  
This wire does not get connected.

Wire connectors provided are for copper wire 
only. For aluminum wire, consult an electrician. 

!

 

 

WARNING! Shock Hazard. May result in serious injury or death. 

Turn off power at circuit breaker before installing the unit.

Single-pole - Switch will be replaced by a dimmer. 
Connect the 

green ground wire on the dimmer to the green or bare ground 

wire in the wallbox. (See 

Important Note 3 at left.)

Connect the 

black wire on the dimmer to one of the wires removed from the 

switch. If you had taped together two wires (see step 4), connect both wires 

to the 

black wire on the dimmer and remove the tape.

Connect the 

red wire on the dimmer to the other wire removed from the 

switch.

Tag

Remove wallplate and the switch mounting screws. Leaving all wires attached, 

carefully pull the switch out from the wall.

Identify switch type. 

Single-pole – The switch will have 

insulated wires connected to two 

screws of the same color plus a green 

ground screw.

Multi-location – 3-way switches will have 

insulated wires connected to three screws 

plus a green ground screw. One of the wires is 

connected to a screw of a different color (not 

green) or labeled COMMON. 

Tag this wire. 

The switch may have two wires attached to the same screw. Tape these two 

wires together before disconnecting. Proceed to disconnect the wires from the 

switch. 

Remove wallplate from the GrafikT

TM

 dimmer and any companion dimmer, but 

leave wallplate adapter connected.

Black 

Tag 

Live 

Blue

Neutral

Green

Green

Dimmer 

Companion 

Dimmer

Light

Red 

Red

Tag 

Black 

Live

Neutral

Blue

Green

Green

Red

Red

Tag

Tag 

Companion 

Dimmer

Dimmer 

Light

Carefully push wires into the wallbox. Install dimmer/companion dimmer(s) and 

snap on wallplate. 

Associate GrafikT

TM

 

dimmer to Clear Connect

®

 devices (GTJ- models only). 

Press and hold the Toggle button on the GrafikT

TM

 dimmer for approximately 6 

seconds. Once all of the light bar LEDs begin to flash, release the Toggle button.

Press and hold the appropriate button on the device (see pictures below) for 

approximately 6 seconds.

Once the dimmer associates the recently added devices, the LEDs and load will 

flash 3 times and the GrafikT

TM

 dimmer will exit set-up mode.

Turn ON power at circuit breaker.

Turn OFF power at circuit breaker.

If needed, set low-end trim. See 

Dimming Operation section (at lower left) for 

details. 

•   Touch to set lights to 

desired level

•  Slide to adjust light level

•   Touch to turn Off or to 

turn On to previous light 

level

•   Toggle button is white 

when On, orange when 

Off

FASS

TM

 - Front Accessible Service Switch

Note: FASS

TM

 is not available on companion 

dimmers.

IMPORTANT NOTICE: FASS

TM

 - Front Accessible Service Switch

To replace bulb(s), power may be conveniently removed by pulling the FASS

TM

 down on the dimmer. After 

replacing bulb(s), push the FASS

TM

 back up fully to restore power to the dimmer.

  Set High-End Trim: 
1.  Press and hold top of 

light bar (approximately 5 

seconds) until Toggle button 

flashes orange. 

2.  Slide finger on light bar to 

adjust to desired brightness. 

3.  To exit, press and hold the 

Toggle button (approximately 

5 seconds) until the Toggle 

button stops flashing.

  Set Low-End Trim: 
1.  Press and hold bottom of 

light bar (approximately 5 

seconds) until Toggle button 

flashes orange.

2.  Slide finger on light bar to 

adjust to desired brightness. 

3.  To exit, press and hold the 

Toggle button (approximately 

5 seconds) until the Toggle 

button stops flashing.

Light does not turn On and no 

LEDs turn On.

•  The FASS

TM

 on the dimmer is pulled down to the 

Off position.

• Light bulb(s) burned out.

• Breaker is OFF or tripped.

• Dimmer is miswired. Check wiring.

Unit is non-responsive.

•  Cycle power to unit by pulling the FASS

TM

 down 

and back up to fully restore power.

Light turns On and dimmer 

works, but companion dimmer 

does not work.

•  Wire connected to the blue wire on the dimmer is 

not the same wire connected to the blue wire on 

the companion dimmer. Check wiring.

•  Wire connected to the red wire on the dimmer is 

not the same wire connected to the red wire on the 

companion dimmer. Check wiring.

Lights repeatedly turn On and 

Off.

•  Load is less than the minimum load. See the 

Minimum Load Chart to determine the acceptable 

minimum load.

Lights are flickering or exhibiting 

poor dimming range.

•  Set low-end trim. See 

Dimming Operation for 

details. 

1

 For performance or compatibility information, Lutron recommends visiting our website 

www.

lutron.com/LED, which is constantly being updated.

Single-pole

0

2 LED lamps

40 W

Multi-location

1

3 LED lamps

80 W

Multi-location

2

4 LED lamps

120 W

Multi-location

3

5 LED lamps

160 W

Multi-location

4

6 LED lamps

200 W

Ground

Different-colored screw

120 V~

60 Hz

Black 

Ground

Red

Blue

Green

Neutral

Live

Dimmer

Light

Ground