Lutron Electronics Company Inc 0111 用户手册

OFF

ON

Hold for 6 seconds  

until LEDs start 

blinking

—and thank you for purchasing a Caséta

TM

 

Wireless in-wall dimmer. In order to control your lights 
from an app or remote, you’ll need to replace an existing 
switch with a CasétaT Wireless in-wall dimmer.

Before you install the dimmer, please watch the 
installation video at  
www.casetawireless.com/support
We hope you enjoy the convenience of Caséta

TM

 Wireless!

NOTE: You can mix and match dimmable LED and 
CFLs, as well as halogen and incandescent light 
bulbs, with Caséta

TM

 Wireless dimmers. 

Dimmable LED and CFL light bulbs vary in their 
dimming performance. If you’re using these  
bulbs and they flicker or turn off, please visit  
www.casetawireless.com/lowend for information 
on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs  
and CFLs, please visit  
www.casetawireless.com/bulblist

Compatible light bulbs include:
Cree

 

BA19-08027OMF-12DE26-1U100 

CR6-575L
EcoSmart

 

ECS BR30 W27 FL 120 

ECS 20 WW FL 50WE 120
Feit

 

A19/OM/LED 
Philips

 

9290002295
Sylvania

 

LED12A19/DIM/O/827 

LED21PAR38/DIM/P/930/FL30

—up to 250 W

—up to 250 W

In-wall dimmer 
(PD-10NXD)

Works with energy efficient 

dimmable light bulbs:

Flat-head screwdriver

Wire connectors

x5

x2

Phillips-head screwdriver

Pliers

Screws

Installation for lights with one wall switch (single pole)

Using your CasétaT Wireless kit

If you have more than one switch controlling the 
light, this is called a 3-way installation. You will need 
to buy PJ2-WALL-WH-L01.  

Please visit 

 for 

more details.

May result in serious injury or death. Turn off 
power at circuit breaker or fuse before installing.

Remove the wallplate from switch.

Remove the switch and pull it away from the wall.

*  If your switch has more than 3 wires attached, see 

“Installing Caséta Wireless in a 3-way switch application” 
video at 

Bend back 
and forth.

Ground

Ground

Ground

Optional

Disconnect all three wires* from the switch.

Connect the bare copper (or green) “ground” wire 
from the wallbox to the green wire on the dimmer 
using a wire connector.

Connect either of the remaining wires from the 
wallbox to either of the remaining wires on the 
dimmer using a second wire connector.

Connect the remaining wire from the wall to  
the remaining wire on the dimmer using a third  
wire connector.

If available, connect the white neutral wire. 
Required for: MLV loads, LED drivers, PHPM-PA, 
PHPM-3F, GRX-TVI.

 remove outside side sections 

on dimmers at the end of gang.

Each dimmer 
has inside side 
sections removed.

Dimmer at middle has all 
side sections removed.

Attach the adapter to the dimmer using the  
screws provided and snap on the wallplate.

(If you installed the dimmer next to other dimmers 
or switches, you’ll need to install a wallplate with the 
correct size/number of openings to accommodate all 
the devices.)

Use the screws provided.

Pairing the dimmer and  

Pico

®

 remote control

Go to 

www.casetawirless.com/support for 

additional troubleshooting suggestions.

Light does not 
turn on or in-wall 
dimmer LEDs do 
not light up.

•  Light bulb(s) burned out.
•  Breaker is OFF or tripped.
•  Light not properly installed.
•  Wiring error.
•   FASS

TM

 switch on the dimmer is 

in the Off position.

Light does not 
respond to Pico

®

 

remote control.

•  The dimmer failed to pair with 

Pico

®

 remote control; see 

remote control.

•  The dimmer is already at the 

light level the Pico

®

 remote 

control is sending.

•  The Pico

®

 remote control 

is outside the 30 ft (9 m) 
operating range.

•  The Pico

®

 remote control 

battery is low.

•  The Pico

®

 remote control 

battery is installed incorrectly.

•  Bulbs turn off 

while being 
dimmed.

•  Bulbs turn on 

at high light 
level but do not 
turn on at a low 
light level.

•  Bulbs flicker 

or flash when 
dimmed to a 
low light level.

Verify bulbs are marked
dimmable and visit  
www.casetawireless.com/
lowend for information on 
adjusting the dimmer for best 
bulb performance.

Love Caséta

TM

 Wireless dimmers? Have ideas 

for making them better? Tell us what you think 
and we’ll extend your warranty by 1 year. 
www.casetawireless.com/register

For advanced features, tips for using Caséta

TM

 Wireless dimmers with CFLs and LEDs, the complete Caséta

TM

 Wireless 

product line, and more, please visit 

Changing the favorite light level 

on the Pico

®

 remote control 

You can use the round “favorite” 
button on the Pico

®

 remote 

control to recall a favorite light 
level. We’ve set it to 50%, but you 
can change it to any level you like.

Favorite

Pull the FASS

TM

 switch out on the in-wall dimmer to 

remove power at the light socket.

Use only with permanently installed fixtures with 
dimmable LED, dimmable CFL, halogen, or 
incandescent,lamps. To avoid overheating and 
possible damage to other equipment, do not use  
to control receptacles, motor-driven appliances,  
or transformer-supplied appliances.

Install in accordance with all national and local  
electrical codes.

When no “grounding means” exist in wallbox, the 
National Electrical Code (NEC

®

) allows a control to 

be installed as a replacement if 1) a nonmetallic, 
noncombustible faceplate is used with nonmetallic 
attachment screws or 2) the circuit is protected by a 
ground fault circuit interrupter (GFCI). When installing 
a control according to these methods, cap or remove 
green wire before screwing control into wallbox.

This device complies with part 15 of the FCC Rules and Industry Canada 
license-exempt RSS standard(s). Operation is subject to the following two 
conditions: (1) This device may not cause interference, and (2) this device 
must accept any interference, including interference that may cause undesired 
operation. Modifications not expressly approved by Lutron Electronics Co., 
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Lutron,  , and Pico are registered trademarks and FASS, Caséta, and 
Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a 
registered trademark of the National Fire Protection Association, Quincy, 
Massachusetts. Google and the Google logo are registered trademarks of 
Google Inc., used with permission.
© 2015 Lutron Electronics Co., Inc

                                                                             P/N 0301778  REV A

Lutron Electronics Co., Inc.  

7200 Suter Road 

Coopersburg, PA  18036-1299, U.S.A. 

Hold for 6 seconds until LEDs  

blink twice on in-wall dimmer.  

New favorite level is now saved.

Important Note: 

Hold for 6 seconds  

until lights flash 3 times.

In-wall dimmer
PD-6WCL
120 V~  50/60 Hz

Important notes:

1. For indoor use only. 
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).

Repeat steps to pair other  
Pico

®

 remote controls.

Wireless

Pico

®

 remote control (sold separately)

On

Off

Darker

Brighter (with raised icon) 

FASS

™

Front Accessible 
Service Switch

In-wall dimmer

On

Off

Darker

Favorite

Brighter

With a smartphone or tablet (Bridge required, sold separately)

The Lutron

®

 app will walk you through 

setting up your devices.

Lutron

The CasétaT Wireless dimmer can be controlled from a smartphone 
when used with the LutronR Smart BridgeT.
 If you are using the dimmer and remote control with the LutronR 
Smart BridgeT follow the instructions below.

Search for “Lutron Caseta”

Lutron

LutronR Smart BridgeT

Note: If you are using the dimmer and remote control with 
another manufacturer’s bridge, please refer to that manufacturer’s 
instructions for set-up.

Lutron

LutronR app

Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Without a smartphone or tablet (Bridge not required)

Warranty
For warranty information, please visit  
www.casetawireless.com/warranty

P/N 0301778  REV A

—up to 1000 W

—up to 1000 W

Control  

three ways

  Add devices 

• PicoR remotes 

• Dimmers 

• Shades  

Schedule  

your lights

Connect  

while away

Important note:

Removing side sections reduces the dimmer’s 

maximum wattage rating. See the chart below  

for maximum wattage information.

* For maximum wattage information when  

  mixing light bulb types see  

 

Maximum* wattage derating chart  
(120 V~  50/60 hz)

LED & CFL

250 W

250 W

250 W

Incandescent, 
Halogen, & MLV

1000 W

800 W

600 W

Switch 1

Switch 2

Using your controls