Lutron Electronics Company Inc 0115 用户手册

Light does 
not turn on or 
dimmer LEDs do 
not light up.

•  Breaker is OFF or tripped.

•  Light not properly installed.

•  Wiring error (see Note under 

Section 4).

•  FASS

TM

 on the dimmer is  

pulled out.

Light does not 
respond to Pico

®

 

remote control.

•  The dimmer failed to pair with 

Pico

®

 remote control; see Pairing 

control.

•  The dimmer is already at the light 

level the Pico

®

 remote control is 

sending.

•  The Pico

®

 remote control is 

outside the 30 ft (9 m) operating 
range.

•  The Pico

®

 remote control battery 

is low.

•  The Pico

®

 remote control battery 

is installed incorrectly.

•  Bulbs turn off 

while being 
dimmed.

•  Bulbs turn on 

at high light 
level but do not 
turn on at a low 
light level.

•  Bulbs flicker 

or flash when 
dimmed to a 
low light level.

Verify bulbs are marked
dimmable and visit  

 

for information on 

adjusting the dimmer for best bulb 
performance.

Top or bottom 
3 LEDs on the 
dimmer are 
blinking.

Dimmer is detecting the wrong 
load type. To change the phase of 
the dimmer, follow instructions at  

Hold for 6 seconds  
until LEDs start 
blinking

—and thank you for purchasing a Caséta

R 

Wireless ELV+ dimmer. In order to control your lights 
from an app or remote, you’ll need to purchase a Pico

R 

remote or Smart Bridge.

Before you install the dimmer, please watch the 
installation video at  

We hope you enjoy the convenience of Caséta

R Wireless!

NOTE: 

You can mix and match dimmable LEDs as 

well as halogen and incandescent light bulbs, with 
Caséta

R Wireless dimmers. 

Dimmable ballasts require low-end trim.

Dimmable LED light bulbs vary in their dimming 
performance. If you’re using these bulbs and they 
flicker or turn off, please visit  

 for information 

on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs 
please visit

  

** When using MLV loads the dimmer must be 
switched to forward phase. Follow the instructions 
at

 

Transformers need to be derated to 75% of rating. 
Contact fixture manufacturer for actual values.

—up to 250 W

ELV+ dimmer (PD-5NE)

Works with energy efficient 
dimmable light bulbs:

Flat-head screwdriver

Wire connectors (4)

Phillips-head screwdriver

Pliers

Screws (2)

Installation for lights with one wall switch (single pole)

R Wireless kit

Some lights have one wall switch, while others 
have two or more wall switches (such as stair lights, 
which have a switch at both the top and bottom of 
the stairs). We’ve included instructions for lights with 
one wall switch (called a single pole). If your light has 
more than one switch (called a 3-way), please visit 

 for complete 

installation instructions or watch “Installing Caseta

R 

Wireless in a 3-way switch application” video found 
at 

May result in serious injury or death. Turn off 
power at circuit breaker or fuse before installing.

*  If your light has more than one switch (called a 3-way), 

follow instructions at 

 

or watch “Installing Caseta

R Wireless in a 3-way switch 

application” video found at  

Bend back 
and forth.

Ground

Ground

Neutral 
required

Ground

Connect the bare copper (or green) “ground” wire 
from the wallbox to the green wire on the dimmer 
using a wire connector.

Connect the Load wire from the wallbox to the red 
wire on the dimmer using a wire connector.

Connect the Hot wire from the wallbox to the black 
wire on the dimmer using a wire connector.

Connect the Neutral wire from the wallbox to the 
white wire on the dimmer.

NOTE:  Dimmer does not work if Hot (Red) and  

Load (Black) wires are reversed and if Neutral 
(White) wire is not connected.

 remove outside side sections 

on dimmers at the end of gang.

Each dimmer 
has inside side 
sections removed.

Dimmer at middle has all 
side sections removed.

Attach the adapter to the dimmer using the  
screws provided and snap on the wallplate.

(If you installed the dimmer next to other dimmers 
or switches, you’ll need to install a wallplate with the 
correct size/number of openings to accommodate all 
the devices.)

Use the screws provided.

Pairing the dimmer and  
Pico

R remote control

Go to 

www.casetawirless.com/support 

for 

additional troubleshooting suggestions.

Love Caséta

R Wireless dimmers? Have ideas 

for making them better? Tell us what you think 
and we’ll extend your warranty by 1 year. 

For advanced features, tips for using Caséta

R Wireless dimmers with CFLs and LEDs, the complete CasétaR Wireless 

product line, and more, please visit

 www.casetawireless.com/features

Changing the favorite light level 
on the Pico

R remote control 

(sold separately) or the dimmer

The round “favorite” button on the 
Pico

R remote control or dimmer 

can be used to recall favorite light 
level(s). Both the Pico

R remote 

control and the dimmer can have 
different favorite light levels. The 
default is 50%, but it can be 
changed to any level.

Use the “brighter” or “darker” 
buttons until the lights are at the a 
desired level.

Favorite

Pull the FASS

TM

 out on the in-wall dimmer to remove 

power at the light socket.

Use only with permanently installed fixtures with 
dimmable LED, dimmable CFL, halogen, or 
incandescent lamps. To avoid overheating and 
possible damage to other equipment, do not use  
to control receptacles, motor-driven appliances,  
or transformer-supplied appliances.

Operating a dimmed magnetic low-voltage circuit with 
all lamps inoperative or removed may result in current 
flow in excess of normal levels. To avoid possible 
transformer overheating or failure, Lutron strongly 
recommends the following:
• DO NOT operate without operative lamps in place.
• Replace burned out lamps as soon as possible.
•  To prevent premature failure due to over-current, use 

transformers with thermal protection or fused primary 
transformer windings.

Install in accordance with all national and local  
electrical codes.

When no “grounding means” exist in wallbox, the 
National Electrical Code (NEC

®

) allows a control to 

be installed as a replacement if 1) a nonmetallic, 
noncombustible faceplate is used with nonmetallic 
attachment screws or 2) the circuit is protected by a 
ground fault circuit interrupter (GFCI). When installing 
a control according to these methods, cap or remove 
green wire before screwing control into wallbox.

This device complies with part 15 of the FCC Rules and Industry Canada 
license-exempt RSS standard(s). Operation is subject to the following two 
conditions: (1) This device may not cause interference, and (2) this device 
must accept any interference, including interference that may cause undesired 
operation. Modifications not expressly approved by Lutron Electronics Co., 
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Lutron,  Lutron, Caséta, 

Lutron

, and Pico are registered trademarks and 

FASS and Smart Bridge are trademarks of Lutron Electronics Co., Inc. 
NEC is a registered trademark of the National Fire Protection Association, 
Quincy, Massachusetts. Google and the Google logo are registered 
trademarks of Google Inc., used with permission.
© 2016 Lutron Electronics Co., Inc

                                                                             P/N 0301833  REV A

Lutron Electronics Co., Inc.  
7200 Suter Road 
Coopersburg, PA  18036-1299, U.S.A. 

Press and hold the “favorite” 
button on either the remote or 
dimmer. Hold for 6 seconds until 
LEDs blink twice on in-wall dimmer.  
New favorite level is now saved.

Important note:

Hold for 6 seconds  
until lights flash 3 times.

ELV+ dimmer
PD-5NE
120 V

~  50/60 Hz

Important notes:

1. For indoor use only. 
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).

Repeat steps to pair other  
Pico

®

 remote controls.

Wireless

Pico

®

 remote control (sold separately)

On

Off

Darker

Brighter 

FASS

™

Front Accessible 
Service Switch

ELV+ dimmer

On

Off

Darker

Favorite

Brighter

With a smartphone or tablet (Bridge required, sold separately)

R app will walk you through 

R app

Lutron

The Caséta

R Wireless dimmer can be controlled from a smartphone 

when used with the Lutron

R Smart BridgeT.

 If you are using the dimmer and remote control with the Lutron

R 

Smart Bridge follow the instructions below.

Search for “Lutron Caseta”

Lutron

Lutron

R Smart Bridge

Note: If you are using the dimmer and remote control with 
another manufacturer’s bridge, please refer to that manufacturer’s 
instructions for set-up.

Lutron

Lutron

R app

Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Without a smartphone or tablet (Bridge not required)

Warranty
For warranty information, please visit  
www.casetawireless.com/warranty

P/N 0301833  REV A

—up to 500 W

R remotes 

Important note:

Removing side sections reduces the dimmer’s 
maximum wattage rating. See the chart below  
for maximum wattage information.

*   For maximum wattage information when mixing 

light bulb types see  

**  When using MLV loads the dimmer must 

be switched to forward phase. Follow the 
instructions at  

~  50/60 Hz)

LED 

250 W

*

250 W

*

250 W

*

Incandescent, 
Halogen & ELV 
Halogen

500 W

*

400 W

*

300 W

*

MLV Halogen**

400 VA

400 VA

400 VA

Dimming Ballasts

400 VA

400 VA

400 VA

LED Drivers

400 W

400 W

400 W

—up to 500 W

—up to 500 W

— up to 400 VA or 300 W 

of lamps

—up to 400 VA

— up to 400 W  

(or 20 drivers max)

R

R

R

R

Favorite

Using your controls