JVC KENWOOD Corporation 452500 用户手册

1

◆  Do not install the repeater in explosive atmospheres (infl ammable 

gas, dust particles, metallic powders, grain powders, etc.).

◆  This repeater is intended for use as a fi xed base station with 

the antenna located outdoors on the rooftop or on an antenna 

tower.

◆  This repeater is designed for a 13.6 V DC power source!  

Never use a 24 V DC or higher source to power the repeater. 

◆  Use only the supplied DC cord.
◆  Do not remove the ferrite core attached to the DC cord. Doing 

so may cause interference with radio communications.

We are grateful you purchased this KENWOOD repeater.  We 

believe this easy-to-program repeater will be highly eff ective in 

your communications system, and will keep personnel operating 

at peak effi  ciency.

•  Do not expose the unit to rain or moisture; to prevent fi re or 

electric shock.

•  Do not open the unit under any circumstances; to avoid risk of 

electric shock.

•  Do not expose the unit to long periods of direct sunlight, nor 

place it close to heating appliances.

•  Do not place the unit in excessively dusty and/or humid areas, 

nor on unstable surfaces.

•  Do not put the plastic bag used for packing of this equipment 

on the place which reaches a small child's hand. It will 
become a cause of suffocation if it wears fl atly.

•  Always switch the transceiver power off before installing 

optional accessories.

•  If you detect an abnormal odor or smoke coming from the unit, 

disconnect the power from the unit immediately.  Contact your 

KENWOOD service center or dealer.

Note: The following unpacking information is for use by your  

KENWOOD dealer, an authorized KENWOOD service center, or the 
factory.

Carefully unpack the repeater. We recommend that you identify 

the items listed in the following table before discarding the packing 

material. If any items are missing or have been damaged during 

shipment, fi le a claim with the carrier immediately.

Hardware fi xture

J21-8559-XX

1

Front glass

B10-2635-XX

1

Name plates

B11-1259-XX

1

Cushion

G13-1801-XX

4

Cushion

G13-1802-XX

4

Foot

J02-0475-XX

2

Foot

J02-0492-XX

2

Grommet

J59-0302-XX

2

Handle

K01-0418-XX

1

Screws

N30-4006-XX

2

Screws

N35-3006-XX

5

DC cord

E30-3427-XX

1

Lead wire with connector (15 pin)

E31-3228-XX

1

Fuse

F05-1537-XX

1

Instruction Manual

B5A-1121-XX

1

To install the handles onto the front panel of the repeater, align the 

handles with the holes on the front panel, then secure the handles 

using the supplied screws.
Please consult your dealer for installing the repeater and antenna.

VHF DIGITAL REPEATER/ UHF DIGITAL REPEATER

INSTRUCTION MANUAL

TKR-D710/ TKR-D810

◆  Government law prohibits the operation of unlicensed radio 

transmitters within the territories under government control.

◆  Illegal operation is punishable by fi ne and/or imprisonment.
◆  Refer service to qualifi ed technicians only.

This equipment generates or uses radio frequency energy.  Changes 
or modifi cations to this equipment may cause harmful interference 
unless the modifi cations are expressly approved by the party 
responsible/JVC KENWOOD. The user could lose the authority to 
operate this equipment if an unauthorized change or modifi cation is 
made.

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that the interference will not occur 
in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

 • 

Reorient or relocate the receiving antenna.

 • 

Increase the separation between the equipment and receiver.

 • 

Connect the equipment to an outlet on a circuit different from that to 
which the receiver is connected.

 • 

Consult the dealer for technical assistance.

The title to and ownership of copyrights for fi rmware embedded in 
KENWOOD product memories are reserved for JVC KENWOOD 
Corporation.

The AMBE+2

TM

 voice coding Technology embodied in this product 

is protected by intellectual property rights including patent rights, 
copyrights and trade secrets of Digital Voice Systems, Inc.  This 
voice coding Technology is licensed solely for use within this 
Communications Equipment.  The user of this Technology is 
explicitly prohibited from attempting to extract, remove, decompile, 
reverse engineer, or disassemble the Object Code, or in any other 
way convert the Object Code into a human-readable form. U.S. 
Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and 
#8,359,197.