VTech Telecommunications Ltd 80-9684-00 用户手册

on purchasing your new VTech product.  

Before using this product, please read 

Important safety instructions.
This manual has instructions on how to 

set up and register your new sensor. For 

instructions on sensor settings, see the 

Abridged user’s manual that came with your 

VC7151/VC7152.
You may also view or download the online 

User’s manual of 

VC7151/VC7152 for a full 

set of installation and operation instructions 

at 

www.vtechphones.com. In Canada, visit  

www.vtechcanada.com.

Your product package contains the following 

items. Save your sales receipt and original 

packaging in the event warranty service is 

necessary.  

Press to open the battery 
compartment case.

Press and hold to enter the 
registration mode.

Red for a second when the sensor is 
powered on.
Flashes red when the sensor is in the 
registration mode.

•

•

•

•

Press the latch button on the sensor to 

open the battery compartment case.
Insert two AAA batteries into the battery 

compartment.

NOTES

Do not mix old and new batteries. Do not 

mix alkaline, standard (Carbon-Zinc) or 

rechargeable (Ni-Cad, Ni-Mh, etc) batteries.
While you insert the batteries, make sure the 

polarities are correct.
The batteries operate properly under the 

temperature between -18°C (0°F) and 50°C 
(122°F).

Add your new 

VC7002 open/closed sensor to 

your 

VC7151/VC7152 telephone system.

Register each sensor with the telephone 

base before use.
To register a open/closed sensor:

Press and hold 

/FIND HANDSET on the 

telephone base for about 4 seconds until 

the 

IN USE light turns on. The telephone 

base shows 

Registering... Please wait.

Press and hold the pair button on the 

open/closed sensor, until the LED light 

flashes red, to enter the registration mode.

The telephone base shows 

registered and you hear a beep when the 

registration process completes. The 

registration process takes about 90 seconds 

to complete.

   Open/Closed X refers to the sensor’s name.

     

X refers to the system-assigned number of the  

     sensor.

1.

2.

•

•

•

1.

2.

VC7002

Accessory Open/Closed Sensor 

for use with

VTech models VC7151/VC7152

User’s manual

User’s manual

Sensor unit

AAA battery x 2

User’s manual

Magnet unit

Spacer of 

sensor unit

Spacers of magnet unit

Double-sided adhesive 

stickers

Screws

Small 

screws

If you have purchased this new 

VC7002 

accessory sensor to replace an old sensor, 
follow the instructions to deregister your 
old sensor. The 

VC7151/VC7152 telephone 

system can support up to 400 sensors.
To replace a sensor, deregister the registered 
sensor first, and then register this new 
sensor to the telephone base.

Press 

MENU when the phone is not in 

use.
Enter the code 

*33734# to access the 

DEREGISTER menu.
Scroll to 

Single sensor, and then press 

.

Scroll to the sensor you want to 
deregister, and then press 

.

Press 

 to confirm the deregistration.

The telephone base shows

is deregistered and you hear a beep when 
the deregistration process completes.

Press 

MENU when the phone is not in 

use.
Enter the code 

*33734# to access the 

DEREGISTER menu.
Press 

 to select 

All sensors.

Press 

 to confirm the deregistration.

The telephone base shows

deregistered and you hear a beep when the 
deregistration process completes.

1.

2.

3.

4.

5.

1.

2.

3.
4.

1.  Separate the sensor unit from the magnet 

unit.

You will hear an announcement alert 

- “Open/Closed X is open”, from the 

handset and the telephone base.
The handset and the telephone base 

will display 

Open/Closed X is open, 

and then  .
The 

SENSOR light on the telephone 

base will turn red.

2.  Combine the sensor unit with the magnet 

unit.

 will disappear from the handset and 

the telephone base.
The 

SENSOR light on the telephone 

base will turn off. 

•

•

•

•

•

You can mount the open/closed sensor on a 

door, window, or medicine cabinet that opens 

or closes.
1.  Take the sensor to the desired mounting 

location, and hold at the object and its 

respective frame.

2.  Open the door, window, or medicine 

cabinet and listen for an announcement 

alert at your handset and telephone base.

Use your handset to enter the 

Settings 

menu, and then the 

Sensor setup menu. 

Follow the steps to test the sensor’s signal 

strength. Move the base closer to the garage, 

or move the sensor closer to the base, if the 

sensor is out of range.

NOTES

Use adhesive tape to hold the sensor 

temporarily whilst testing.
Mount the sensor to a higher position to 

avoid obstacles or blockages. Depending on 

surroundings and obstructing factors, like walls 

or cabinets, the sensor may not transmit to the 

base properly.

•

•

Mount with sticker
1.  Attach the sticker 

C onto the rectangular 

area at the rear side of the magnet unit,

2.  Stick the magnet unit onto the door.

Mount with sticker
You can choose one out of the four spacers 

with suitable height, and then add it to the 

magnet unit.
1.  Push the spacer towards the magnet unit 

until it securely clicks into place.

2.  Attach the sticker 

C onto the rectangular 

area at the rear side of the spacer.

3.  Stick the magnet unit onto the door.

Go to www.vtechphones.com 
to register your product for 
enhanced warranty support and 
the latest VTech product news.

We recommend you to mount the magnet unit 
on a door, window, or medicine cabinet, and 
mount the sensor unit on its respective frame.

NOTES

Make sure the mounting surface is clean. 
A textured surface or any imperfections to 
a smooth surface can keep the sticker from 
making a strong bond.
Make sure you align the magnet unit with 
sensor unit when mounting.
The distance between the sensor unit and 
magnet unit must be 

less than 1 cm (0.4 inch).

The door images in this installation guide are 
for conceptual reference only.

TIPS

If there is a difference in level between the door, 
window, or medicine cabinet and its respective 
frame, or the frame is too narrow or has some 
decorative molding, you can choose to mount 
the open/closed sensor with spacer. You can 
also mount the magnet unit on the frame, 
and the sensor unit on the door, window, or 
medicine cabinet instead.
You can choose to mount the sensor unit with 
sticker first, and then use screws later if you 
decide to mount it at that location for long term.

•

•

•

•

•

•

cc