Everspring Industry Co Ltd CC425 用户手册

1 

 

 

 

 

 

  Installation and Operating Manual 

The 2.4G Wireless Camera is designed to provide safety, 
security, convenience to your home and business. At home, 
it sees and hears baby's room, garage, or any other room 
from somewhere else in the house.  In business, it 
monitors entry/exit ways, reception area, storage-rooms, 
warehouses from one central location.  It is so 
user-friendly that you can complete the installation in a few 
minutes.  

The components included in the 2.4G Wireless Camera Kit: 

 

1 x Camera Unit build in 2.4G transmitter 

 

1 x A/V Receiver Unit build in 2.4G receiver   

 

1 x 9V 500mA AC adapter (for PIR Camera unit) 

 

1 x 12V 500mA AC adapter (for Receiver unit) 

 

6-foot SCART to RCA (European) or RCA to RCA 
(USA) cable   

 

Fixing and Owner’s manual 

 

Do not attempt to open the sealed camera case: as this 

will destroy its weather resistance properties and void 
the system's warranty. 

 

 

Disconnect the system. Always disconnect the system 

from your mains power supply during installation. 

 

 

Keep a light source during nighttime. The camera 

cannot work in total darkness. Please bear in mind the 
camera's viewing area must be illuminated with a 
suitable light source. 

 

●       

Avoid the camera pointing directly at a light source. 
When installing the camera outdoor, you should ensure 
that the camera lens will not become dusty easily, and 
the camera does not point directly at a light source (e.g. 
direct lighting, or sun light) (Fig. 1), as the picture 
quality will be impaired. Additionally, the camera must 
be positioned so that it will not point directly into the 
sun (sunrise or sunset) or any bright light, as this may 
cause damage to the camera.    The best viewing angle 
is achieved at greater heights (e.g. 2.5 to 3m) with the 
camera pointing down.  Also, avoid viewing areas 
where half the area is in bright sunlight and the other 
half is dark. (Fig. 2)

 

 

Fig. 1 

 

 
 
 
 
 

Fig. 2 

●       

Test before you mounting your camera permanently. It 
is recommended that before mounting your camera 
permanently, you temporarily connect your system to 
your television or monitor.  You can then test your 
system and determine the best position for your 
camera. 

 

 

Do not over tighten the camera.  Your  camera  is  fully 

adjustable both horizontally and vertically via a ball and 
socket joint, which is secured with a tension screw.  
The tension screw can be locked into position using the 
Allen key supplied once your installation is complete.  
Do not over tighten as this may stop you from 
loosening the screw to make any slight adjustment in 
the future.  Retain the Allen key for future use. 

 

●     

Detecting sensitivity: A passive infrared sensor operates 
by detecting the objective movement and heat.    When 
the temperature of the moving object and its 
surrounding area are close in value, it may reduce PIR’s 
sensitivity.  The motion detector’s infrared beams 
radiate outward like the slat of a wooden fence.    Prior 
to mounting, keep in mind that the motion sensor is 
more sensitive to the motion that crosses these “slat”, 
and less sensitive to the motion that moves directly 
towards the sensor.

 

 

 

Your camera has been designed to prevent 

condensation when installed outside or in damp 
conditions.  For this to work correctly the camera 
should be left connected to the mains power supply 
and switched on permanently. 

Having tested your camera and being familiar with the 
temporary test set, you can assess the best location for the 
camera.  Ideally you will need one person to hold the