Everspring Industry Co Ltd TR009-01 用户手册
1
Motion Detector SP804
Installation and Operating Instructions
These instructions should be read in conjunction with
your system installation, and they should be retained
for future reference.
your system installation, and they should be retained
for future reference.
PRODUCT LAYOUT
Lens Cover (wall-lens cover & ceiling-lens cover)
Light Sensor
PIR Sensor
Two-Color Indication LED (red & green)
Learning Key
Light Sensor
PIR Sensor
Two-Color Indication LED (red & green)
Learning Key
INTRODUCTION
The Motion Detector is designed with two detecting
sensors, Passive Infra-Red (PIR) sensor and light sensor,
to detect movement within a protected area, operating at
868.30/923 MHz only.
The detector can be used as a security device or home
automation device. When the detector is cooperated with
security appliances, the detector is acting as a security
device by detecting changes in infra-red radiation levels.
If a person moves within or across the devices field of
vision, a trigger radio signal will be transmitted to cause full
alarm condition in order to frighten intruders away.
Alternatively, when the detector is worked with Everspring
USB Dongle (SA804), the detector can be set to perform
the role of home automation device by detecting both
changes in infra-red radiation levels and percentage of lux
levels. Once night falls, the percentage of ambient
illumination is lower than preset value. If a person moves
within or across the devices field of vision, a trigger radio
signal will be transmitted so as to turn connected lightings
for better illumination.
Two mounting methods are provided for varying detection
sensors, Passive Infra-Red (PIR) sensor and light sensor,
to detect movement within a protected area, operating at
868.30/923 MHz only.
The detector can be used as a security device or home
automation device. When the detector is cooperated with
security appliances, the detector is acting as a security
device by detecting changes in infra-red radiation levels.
If a person moves within or across the devices field of
vision, a trigger radio signal will be transmitted to cause full
alarm condition in order to frighten intruders away.
Alternatively, when the detector is worked with Everspring
USB Dongle (SA804), the detector can be set to perform
the role of home automation device by detecting both
changes in infra-red radiation levels and percentage of lux
levels. Once night falls, the percentage of ambient
illumination is lower than preset value. If a person moves
within or across the devices field of vision, a trigger radio
signal will be transmitted so as to turn connected lightings
for better illumination.
Two mounting methods are provided for varying detection
range. The detector can be mounted on a wall for farther
detecting distance but narrower coverage; while for ceiling
mounting, shorter detecting distance can be made but
desired coverage can be expected at user’s disposal.
The Motion Detector is powered by 3 x AA 1.5V alkaline
battery. When battery level drops below unacceptable
level, the red LED will flash once every 30 seconds and
transmit radio signal to the control panel. When this
occurs, replace the batteries as soon as possible.
detecting distance but narrower coverage; while for ceiling
mounting, shorter detecting distance can be made but
desired coverage can be expected at user’s disposal.
The Motion Detector is powered by 3 x AA 1.5V alkaline
battery. When battery level drops below unacceptable
level, the red LED will flash once every 30 seconds and
transmit radio signal to the control panel. When this
occurs, replace the batteries as soon as possible.
CHOOSING A MOUNTING LOCATION
The Motion Detector can be mounted either on a wall or
under a ceiling. Before selecting a position for a Motion
Detector the following points should be noted:
under a ceiling. Before selecting a position for a Motion
Detector the following points should be noted:
1.
Do not position the detector facing a
window/fan/air-conditioner or direct sunlight. Motion
Detectors are not suitable for use in conservatories or
draughty areas.
window/fan/air-conditioner or direct sunlight. Motion
Detectors are not suitable for use in conservatories or
draughty areas.
2. Do not position the detector directly above or facing
any source of heat, e.g. fires, radiators, boiler etc.
3. Where possible, mount the detector so that the logical
path of an intruder would cut across the fan pattern
rather than directly towards the detector (FIGURE 1).
rather than directly towards the detector (FIGURE 1).
FIGURE 1
4. For best results, position the detector directly facing
entrance.
5. Ensure that the position selected for the Motion
Detector is within effective range of the system (refer
to System Installation and Operating Manual).
to System Installation and Operating Manual).
INSTALLING THE MOTION DETECTOR
The unit can apply two ways of installations. Select a
location for the unit based on the coverage angles shown
in FIGURE 4b and FIGURE 5b. To install a detector:
1. Undo and remove the screw from the bottom edge of
the detector to detach the rear cover (FIGURE 2).
Inside View
Rear View
Front View