Visonic Inc. SPD1000 用户手册

2

DE3652

Before detector installation:

  1 .  Remove spring movement prevention sticker (see fig. 5).

  2 .  Remove protective non-metallic spacer that keeps the

spring in the “sleep” mode (shown in par. 3.7).

3.2 Setting the SMD Switches

SW. 1 Sensitivity

& tracking

ON Spider: Tracking enabled

PowerArt: High sensitivity

ON

OFF Spider: Tracking disabled

PowerArt: Low Sensitivity

SW. 2 Buzzer

ON Enabled

ON

OFF Disabled

SW. 3 Supervision ON USA (60 Min.)

ON

OFF Europe (15 Min.)

SW. 4 Mode

ON SpiderAlert

ON

OFF PowerArt or MCR-308

3.3 Preparation for Use

3.4 Teaching PowerArt / MCR-308

Teach PowerArt / MCR-308 to identify SPD-1000:
  A .  Teach PowerArt (see par. 3.2G in PowerArt Prog. Guide) or

MCR-308 (see par. 3.5 in MCR-308 installation instructions).
When instructed to transmit, initiate SPD-1000 low severity
alarm transmission by momentarily pressing the Reset switch
(see illustration 1 in par. 3.3).  

    Note: According to this signal, the PowerArt automatically learns

learns to identify low severity alarm only.  

    To teach the MCR-308 the high severity alarm, create the alarm

  B .  Verify that the teaching is successful, according to the

previously mentioned documents.

3.5 Teaching the SpiderAlert System

Teach SpiderAlert system to identify SPD-1000 transmissions:
  A .  In SpiderAlert software Click File/Transmitters/Museum/Add.
  B .  Initiate low severity alarm transmission by momentarily

pressing Reset switch (see par. 3.3, step 1).

  C .  The detector’s ID number will be displayed in the yellow box.
  D .  Press the “<<” button to move the ID number from the yellow

(temporary) box to the “ID” box.

  E .  In the Location box, type the secured object's name (i.e.

Mona Liza picture).

  F .  In Holder Group box, type a desired name for the museum

detectors group for whom the event handling will be identical.

  G .  Press the          button, to display the Museum Group screen.
  H .  Select the appropriate museum detectors group.
  I .  Press Edit button, define (for the operator) the handling

description for every detector’s event and press OK.

3.6 Operation

SPD-1000 function is based on magnetic field changes as a

result of the secured object movements. The detector has 2

detection levels - low severity alarm (continuous slight touch) and

high severity alarm (strong touch or removal).
Once stabilized, the detector checks its position continuously.

Upon a movement detection, the detector sends alarm as follows:

stabilization period at least, for the next movement detection.
When Low or High level alarm is

transmitted, 2 weak buzzer sounds are

heard, as shown.

3.7 Entering the “Sleep” Mode

Entering Sleep mode (for description, see section 1) is as follows:

This device complies with FCC Rules Part 15. Operation is subject to two

conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference that may be received or that may cause

undesired operation. The user is cautioned that changes or modifications to

the unit, not expressly approved by Visonic Ltd., could void the user's FCC or

other authority to operate the equipment

The 315 MHz is for USA & Canada - not allowed in any EU member state. The

433.92 MHz has no restriction in any EU member state.

                                    

VISONETIX LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6890, FAX: (972-3) 645-6891
VISONIC SYSTEMS INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 242-9945, (800) 874-3989 FAX: (860) 242-0191
VISONIC LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: (01767) 600857 FAX: (01767) 601098
VISONETIX LTD. 2001   SPD-1000   DE3652-  (REV. 5,  12/2001)

Separate warranty statement is enclosed.         www.visonetix.com

 ...