Tyco Safety Products/Sensormatic DMS915 用户手册
Setup and Service Guide
8000-0395-02, Rev. B (10 pages)
MICROWAVE PRODUCTS
1
1
Digital Microwave
System 915
Addendum
Addendum
EADC12WC DMS Concealed 12'
EADC18WC DMS Concealed 18'
EADC24WC DMS Concealed 24'
EADM06
EADC18WC DMS Concealed 18'
EADC24WC DMS Concealed 24'
EADM06
DMS Micromax 6'
EADM06WC DMS Micromax WC 6'
EADM12
EADM12
DMS Micromax 12'
EADM12WC DMS Micromax WC 12'
EADM18
EADM18
DMS Micromax 18'
EADM18WC DMS Micromax WC 18'
EADM24
EADM24
DMS Micromax 24'
EADP06
DMS Pedestal 6'
EADP18WC DMS Pedestal WC 18'
EADR03WC DMS Sensormat II 3'
EADR06WC DMS Sensormat II 6'
EADR10WC DMS Sensormat II 10'
EADS03
EADR03WC DMS Sensormat II 3'
EADR06WC DMS Sensormat II 6'
EADR10WC DMS Sensormat II 10'
EADS03
DMS Slimline 3'
EADS06
DMS Slimline 6'
Contents
About this Guide
.................................................... 1
About the DMS 915
............................................... 2
Board Replacement
............................................... 2
Antenna Connection Change
................................ 2
Tuning Procedure
.................................................. 3
Typical Installations
............................................... 4
Specifications
........................................................ 8
Declarations
........................................................ 10
About this Guide
This Setup and Service guide explains board
replacement, an antenna connection change,
tuning, and typical installations for the DMS 915
detector with the redesigned RF Transmitter/
Receiver Board. It is intended to be used as a
supplement to the DMS 915 Installation and Field
Service Manual, 8000-0395-01. Refer to the DMS
915 manual for a complete description of theory,
installation, and trouble-shooting.
replacement, an antenna connection change,
tuning, and typical installations for the DMS 915
detector with the redesigned RF Transmitter/
Receiver Board. It is intended to be used as a
supplement to the DMS 915 Installation and Field
Service Manual, 8000-0395-01. Refer to the DMS
915 manual for a complete description of theory,
installation, and trouble-shooting.
Note: Because customer requirements dictate the
placement of detector components, your
Sensormatic representative will supply this
information separately.
placement of detector components, your
Sensormatic representative will supply this
information separately.
If you need assistance...
Call Sensormatic Customer Support at:
1-800-543-9740
Micromax, Sensormatic, and the Sensormatic logo are
registered trademarks of Sensormatic Electronics Corporation.
Other product names (if any) mentioned herein may be
trademarks or registered trademarks of other companies.
registered trademarks of Sensormatic Electronics Corporation.
Other product names (if any) mentioned herein may be
trademarks or registered trademarks of other companies.
No part of this guide may be reproduced in any form without
written permission from Sensormatic Electronics Corporation.
written permission from Sensormatic Electronics Corporation.
© Copyright 2001. All rights reserved.
(DOJ) 01/01
The RF Transmitter/Receiver Board was
redesigned because some components on the
board were no longer available. This
addendum contains the tuning procedure and
service information for the new board.
redesigned because some components on the
board were no longer available. This
addendum contains the tuning procedure and
service information for the new board.
Note to Installers:
For FCC compliance, system components must
be located where persons are not likely to linger
within 20cm (8") of the RF antennas. A 20cm (8")
setback is not required provided the antenna
location does not promote lingering within 20cm
(8") of the antennas. For example, do not locate
antennas adjacent to a chair or bench.
For FCC compliance, system components must
be located where persons are not likely to linger
within 20cm (8") of the RF antennas. A 20cm (8")
setback is not required provided the antenna
location does not promote lingering within 20cm
(8") of the antennas. For example, do not locate
antennas adjacent to a chair or bench.