Foxpro Inc 623 用户手册
Instructions to Integrators for use of the FOXPRO
505MOD Modular Transmitter
The 505MOD modular transmitter has received regulatory approvals in accordance with
FCC CFR47 Part 15 Subpart C 15.249 and with Part 15.212 Modular Transmitter
Approval for modular devices in the United States, and Industry Canada under RSS-210
and RSS-Gen. in Canada. This approval allows for the incorporation of the module inside
finished products without the need for regulatory testing for an intentional radiator (RF
transmitter) provided no changes are made to the module circuitry. Changes or
modifications to the module could void your authority to market products containing the
module. Integrators must comply with these instructions so as to ensure compliance with
FCC and Industry Canada regulations.
The only antenna authorized for use with the 505MOD modular transmitter is a single
element ¼ wave monopole made of wire with a length of 3.1 inches, plus or minus 0.1
inches.
The products that contain the module must be labeled in accordance with Part 15.19 on
the outside of the product so as to be easily seen by the consumer. The label must be
permanent and include the following information and statements:
“Contains FCC ID: C6M623 IC: 8027A-515
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.”
Also, the user manual for any product containing the module must include the following
statement:
“This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and ON, the
user is encouraged to try to correct the interference by one or more of the following
measures:
FCC CFR47 Part 15 Subpart C 15.249 and with Part 15.212 Modular Transmitter
Approval for modular devices in the United States, and Industry Canada under RSS-210
and RSS-Gen. in Canada. This approval allows for the incorporation of the module inside
finished products without the need for regulatory testing for an intentional radiator (RF
transmitter) provided no changes are made to the module circuitry. Changes or
modifications to the module could void your authority to market products containing the
module. Integrators must comply with these instructions so as to ensure compliance with
FCC and Industry Canada regulations.
The only antenna authorized for use with the 505MOD modular transmitter is a single
element ¼ wave monopole made of wire with a length of 3.1 inches, plus or minus 0.1
inches.
The products that contain the module must be labeled in accordance with Part 15.19 on
the outside of the product so as to be easily seen by the consumer. The label must be
permanent and include the following information and statements:
“Contains FCC ID: C6M623 IC: 8027A-515
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.”
Also, the user manual for any product containing the module must include the following
statement:
“This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and ON, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.