Fisher Price N596208 用户手册
www.fisher-price.com
• Please keep this instruction sheet for future
reference, as it contains important information.
• Requires two 9V (6LR61) alkaline batteries (not
included) for operation.
• Adult assembly is required for
battery installation.
• Tool required for battery installation: Phillips
screwdriver (not included).
• Transmission carrier frequency is 27.145 MHz.
• Walkie talkie range is up to 200 feet (61 meters).
• Field strength: 74.8dBu V/m at 3m.
• Walkie talkie range is up to 200 feet (61 meters).
• Field strength: 74.8dBu V/m at 3m.
Troubleshooting Guide
Problem
Cause
Solution
Excessive static
Interference from vehicles,
power lines, fl uorescent lights,
electric motors or dimmer
switches
power lines, fl uorescent lights,
electric motors or dimmer
switches
Change your location.
Point the antenna in a different
direction.
direction.
Can hear other people talking
Transmissions on the same
frequency as this product
frequency as this product
This product operates on
a public frequency and
may occasionally pick up
transmissions from other
transmitting devices on the
same frequency.
a public frequency and
may occasionally pick up
transmissions from other
transmitting devices on the
same frequency.
Walkie talkie does not work
Walkie talkie power is off
Make sure both walkie
talkies’ power is on
talkies’ power is on
Battery power is low
Replace the exhausted battery
in each walkie talkie. See
Battery Installation section on
this sheet.
in each walkie talkie. See
Battery Installation section on
this sheet.
Walkie talkies are out of range
The walkie talkies can transmit
up to 200 feet. Decrease the
distance between the units.
up to 200 feet. Decrease the
distance between the units.
Walkie talkie range decreases
Units do not transmit well
through large objects
through large objects
Indoor range may be lower
because of walls or large
objects between the walkie
talkies. Make sure there is a
clear path between the units.
because of walls or large
objects between the walkie
talkies. Make sure there is a
clear path between the units.
Battery power is low
Replace the exhausted battery
in each walkie talkie. See
Battery Installation section on
this sheet.
in each walkie talkie. See
Battery Installation section on
this sheet.
Power L.E.D. is off
Power is OFF
Turn the power/volume dial to
the ON position.
the ON position.
Walkie talkie is in sleep mode
The walkie talkie goes into
sleep mode after 5 minutes of
inactivity. Press the talk button
to “wake it up”.
sleep mode after 5 minutes of
inactivity. Press the talk button
to “wake it up”.
Battery power is low
Replace the exhausted battery
in the walkie talkie. See Bat-
tery Installation section on
this sheet.
in the walkie talkie. See Bat-
tery Installation section on
this sheet.
6
Tough for Talking
5
• Turn the power/volume dial on the front of each walkie talkie to turn them on. The power L.E.D.
lights to indicate that power is ON.
• Press and hold the talk button on the side of the walkie talkie and talk into the microphone.
• Release the talk button to listen to a response from the other walkie talkie!
• Walkie talkie range is dependant on environmental conditions. The range of the walkie talkies will
• Release the talk button to listen to a response from the other walkie talkie!
• Walkie talkie range is dependant on environmental conditions. The range of the walkie talkies will
be shorter when used indoors than it will when used outdoors.
• After fi ve minutes of inactivity, the walkie talkies will go into sleep mode. Press the talk button to turn
it back on.
IMPORTANT! Always remember that you are using public frequencies when using these walkie
talkies. You may fi nd that this product will occasionally pick up transmissions from other transmitting
devices using the same frequency.
talkies. You may fi nd that this product will occasionally pick up transmissions from other transmitting
devices using the same frequency.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifi cations not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifi cations not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
N5962