Honeywell International Inc. 8DL5800RL-2 用户手册

K3790V1  6/07  Rev. A

ADEMCO 5800RL

 

Wireless Relay Module

The ADEMCO 5800RL is a Wireless Relay Module that 
enables use of remote sounders and/or remote arm/disarm 
indicators using two relays activated by wireless signals from 
the LYNX control (see Figure 1). The 5800RL can also send 
tamper and supervision signals to the LYNX if so 
programmed. The 5800RL is compatible with LYNX controls 
having software versions 9.0 or higher.  Refer to the LYNX 
control installation and setup guide for software compatibility 
and zone programming information. 
 

RELAY

MODULE

TAMPER AND

SUPERVISION

SIGNALS SENT

TO CONTROL

MODULE'S 2

RELAYS ARE

ACTIVATED BY

SYSTEM

CONDITIONS

5800RF-004-V0

 

 

 
MOUNTING LOCATION GUIDELINES 
Use the following guidelines when selecting a mounting 
location for the 5800RL Relay Module (see Figure 2): 
•  Mount the 5800RL in a high location for best wireless 

reception. 

•  Do not mount the 5800RL on or near metal objects. This 

decreases range and/or blocks wireless transmissions. 

•  Locate the 5800RL at least 10 feet from any remote 

keypad to avoid interference from the microprocessors in 
those units. 

•  To avoid voltage loss that occurs on long power lines, 

mount the external power supply unit in close proximity to 
the 5800RL. 

 

 

 

IMPORTANT:  Before permanently mounting the 5800RL, 
perform the setup procedure described in the 

the 5800RL section. 

1.  Remove the 5800RL's cover from the base (using a small 

flat head screwdriver, insert screwdriver’s tip in slot at top 
of the cover and twist). 

 

2.  Using the 5800RL base as a template, position in the 

desired location and mark the two mounting holes. See 
Figure 2 for mounting hole locations. 

3.  Attach the 5800RL base using the fasteners supplied. 

Screws and plastic anchors are suitable for a typical 
installation, but you may use any two fasteners that 
secure the base firmly to the mounting surface. 

4. Connect relay and power wiring to the 5800kRL’s 

terminals. Refer to Figure 3 for a typical relay application. 

The 5800RL can be powered from either an AC transformer 
or DC power supply external power source connected to 
terminals 7 and 8 (see Figure 3). 
Power source ratings and connections are as follows: 

AC 

9VAC, 15VA 

terminals 7 and 8 

Ademco 1332 

DC 9VDC, 

100mA 

N7703 

 

 

terminals 7 and 8 
or plugged into 
power connector. 

 

NOTE:  Use of power sources with higher or lower voltages 
may result in damage or failure to operate properly. Non-
ADEMCO power supplies may have connectors installed. 
Remove these connectors prior to attempting to connect 
power supply to 5800RL. 

 

TAMPER

SWITCH

2 - NO

3 - COM

4 - NC

5 - NO

6 - COM

7 - AC OR DC (+) IN

1 - NC

8 - AC OR DC (  ) IN 

RELAY A

RELAY B

5800RL-001-V1

LED

(RED)

LED

(YELLOW)

LED

(GREEN)

RF INTERFERENCE

LED (RED)

ANTENNA 2

ANTENNA 1

DIP

SWITCH

MOUNTING

HOLE

MOUNTING

HOLE

1 2 3 4 5 6

ON
OFF

 

2 - NO

3 - COM

4 - NC

5 - NO

6 - COM

7 - AC OR DC (+) IN

1 - NC

8 - AC OR DC (  ) IN 

RELAY A

RELAY B

5800RL-005-V0

ANTENNA 2

SOUNDER

ANTENNA 1

1 2 3 4 5 6

ON
OFF

AC

IN

+

_

DC

OUT

+

_

RED

BLA

CK

POWER SUPPLY

BACKUP

BATTERY 12VDC

+

PWR SUPPLY

XFMR

16.5VAC

Refer to RELAY and LED Operation section and DIP Switch 
(Figure 4) in order to set up the 5800RL as follows:

 

5.  Set DIP switches 3-6 (Figure 4) to the appropriate House 

ID (1-31). Make sure the House ID set by the DIP 
switches matches that entered in the LYNX control. 

6.  If module supervision and/or tamper protection is desired, 

program the 5800RL’s tamper/supervisory loop (1) as a 
zone and enroll its serial number. 

Note the following when enrolling: 

Zone Type = 5 (trouble by day/alarm by night) 
Input Type = 3 (RF) 
Loop Number = 1 

PLEASE GO TO THE BOTTOM RIGHT OF PAGE 2