Honeywell International Inc. 8DL6160RF 用户手册
Preliminary - 6 September 2002
2
INSTALLING THE 6160RF
Locate the 6160RF in an area and at a height where it is
convenient for user operation. The 6160RF must be at
least 10 ft from the control panel to ensure proper
operation of the RF receiver.
convenient for user operation. The 6160RF must be at
least 10 ft from the control panel to ensure proper
operation of the RF receiver.
Mounting And Wiring
The 6160RF has terminal blocks for connection to power
and data wires, and relay contact wires. Removing the
keypad’s case back accesses these terminal blocks.
and data wires, and relay contact wires. Removing the
keypad’s case back accesses these terminal blocks.
The 6160RF can be surface mounted directly to walls, or
to a single- or double-gang U.S./Italian style electrical box.
Follow these steps to mount and wire the keypad:
to a single- or double-gang U.S./Italian style electrical box.
Follow these steps to mount and wire the keypad:
1. Detach the case back by pushing up into one of the two
slots at the bottom of the keypad with the blade of a
small screwdriver (this will push in the release snap),
then pull that side of the case back away. Repeat for
the other side. Refer to Figure 1 for location of the case
back release snaps.
small screwdriver (this will push in the release snap),
then pull that side of the case back away. Repeat for
the other side. Refer to Figure 1 for location of the case
back release snaps.
ARMED
READY
MOUNTING
RELEASE
SNAPS
NOTE:
TO REMOVE REAR COVER
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT COVER UP.
TO REMOVE REAR COVER
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT COVER UP.
6164RF-003-V0
Figure 1. Removing the Case Back
2. Pass the wiring from the control panel through the
opening in the case back. (see the control panel’s
instructions for proper run lengths.)
instructions for proper run lengths.)
a. If surface wiring is being used, wiring may be
routed through the top or the bottom left-side
breakout in the case back. See Figure 2. The
breakouts must be punched out using a screwdriver
before mounting the case back.
breakout in the case back. See Figure 2. The
breakouts must be punched out using a screwdriver
before mounting the case back.
b. If desired, wires may be strain-relieved to the wire
tie point on the inside of the case back with a tie
wrap (not supplied).
wrap (not supplied).
3. Mount the case back to a wall or to an electrical box
using the 25mm-long self-tapping screws supplied
(mollies for drywall are not supplied).
(mollies for drywall are not supplied).
Note: If you wish to tamper-protect the keypad for removal from the
wall, use an additional mounting screw in the tamper hole in
the case back (see Figure 2 for location).
the case back (see Figure 2 for location).
4. Connect the power and data wires from the control
panel to the terminals on the 6160RF as indicated
Figure 3 and Table 1.
Figure 3 and Table 1.
G
6160RF-002-V0
Y +
TAMPER
SWITCH
WIRING TERMINALS
(TO CONTROL PANEL)
+ +
+ +
Figure 3 - 6160RF Wiring Details
Table 1 - Wiring Table
Keypad
Control Panel
Wire Color
▲
G
Data In
Green
-
-Aux Pwr (GND)
Black
+
+Aux Pwr
Red
y
Y
Data Out
Yellow
5. Re-attach the keypad to the mounted case back.
Attach the top of the keypad first, and then press the
bottom section down until it snaps into place securely.
bottom section down until it snaps into place securely.
6. Peel off protective film on the LED panel and install the
keypad labels as required.
6160RF PROGRAMMING
Entering Program Mode
Press the [1] and [3] keys simultaneously for a few seconds within 30 seconds after applying power or within 30 seconds after
removing the case back. The current keypad address
removing the case back. The current keypad address
CON ADDRESS = XX
will be displayed. Press the [
✳
] key.
Programming Operations
Once you have entered the Program mode, you may advance between prompts by pressing the [✳] key. This will also store
displayed information.
displayed information.
Programming the 6160RF
Note: Refer to the control panel’s installation instructions for the acceptable keypad and receiver addresses.
•
If you are using a wireless key in High-Security mode (e.g.;5804E) in the control panel, it will occupy one of the devices in the
6160RF.
6160RF.
•
When operating the system in High-Security mode, only encrypted wireless keys will function.