Honeywell International Inc. 8DLLYNXREN-5 用户手册
–21–
Data Field Descriptions
✻
49
Split/Dual Reporting
To Primary
To Secondary
0 = All reports
None, unless primary
fails, then all
1 = Alarms, Restore, Cancel*
Others
2 = All except Open/Close, Test
Open/Close, Test
3 = Alarms, Restore, Cancel
All
4 = All except Open/Close, Test
All
5 = All reports
All
To Primary
To Paging Number
6 = All reports except Open/Close Alarms, Open/Close ‡,
Troubles
7 = All reports
Alarms, Troubles
8 = All reports
Alarms, Open/Close ‡,
Troubles
9 = All reports except Open/Close Open/Close ‡
To Primary
To Follow Me System
Phone
Number
10=All reports except Open/Close Alarms, Open/Close ‡,
Troubles
11 = All reports
Alarms, Troubles
12=All reports
Alarms, Open/Close ‡,
Troubles
13=All reports except Open/Close Open/Close ‡
*Recent close report is sent to primary number
‡ Will report Users 0, 5-8, and, if using wireless button-type
*Recent close report is sent to primary number
‡ Will report Users 0, 5-8, and, if using wireless button-type
devices, will report the zone number of the arm or disarm
button 26-33. All other zones and users are not reported.
button 26-33. All other zones and users are not reported.
This field is used to select a reporting option as follows:
Enter: 0 - 5 when reporting to telephone receivers.
Enter: 0 - 5 when reporting to telephone receivers.
6 - 9 when reporting to a pager is desired.
10 - 13 when reporting to an auxiliary telephone receiver.
Pager Report Format
Options 6-9 send reports to the primary phone number, in a format defined
in Field
Options 6-9 send reports to the primary phone number, in a format defined
in Field
✻
48, and send reports to a pager, which has its phone number
entered as the secondary phone number in Field
✻
42. The pager report is a
7-digit code, with optional 16-digit prefix, in the following format:
AAAAAAAAAAAAAAAA-EEE–00NN where:
AAA = Optional 16 digits for PIN number, etc. See Field
AAAAAAAAAAAAAAAA-EEE–00NN where:
AAA = Optional 16 digits for PIN number, etc. See Field
✻
88 for full
description of these characters.
EEE = 3-digit Event Code as follows:
911 = Alarm (NN = zone number)
101 = Open, system disarmed (NN = user no.)
102 = Close, system armed (NN = user no.)
811 = Trouble (NN = zone no.)
00 =
911 = Alarm (NN = zone number)
101 = Open, system disarmed (NN = user no.)
102 = Close, system armed (NN = user no.)
811 = Trouble (NN = zone no.)
00 =
Always displayed before 2-digit user/zone no.
NN =
2-digit user number or zone number, depending on the type of
event (EEE) that occurred.
event (EEE) that occurred.
Follow Me System Report Format
Options 10-13 send reports to the primary phone number, in a format
defined in Field
Options 10-13 send reports to the primary phone number, in a format
defined in Field
✻
48, and sends voice message to the secondary phone
number entered in Field
✻
42.
The message is a repeatable system status announcement. If the manual
paging option has been programmed in Field
paging option has been programmed in Field
✻
87, the message will repeat
“system, system…..”.
The message can be terminated by pressing any key on the telephone
keypad.
keypad.
✻
50
Burglary Abort Window
0 =No abort window
1 = 15-second abort window
2 = 30-second abort window
3 = 45-second abort window
SIA Abort Window time options: 1 = 15 secs; 2 =
30 secs; 3 = 45 secs
0 = refer to Entry delay set in field *35
This provides the option for an Abort Window for Burglary zone types that
report to the central station. This feature allows time for the subscriber to
avoid a false alarm transmission. This feature does not apply to zone type 9
alarms (Supervised Fire) or to 24-hour zone types 6, 7, and 8 (silent panic,
audible alarm, auxiliary alarm), which are always sent as soon as they occur.
report to the central station. This feature allows time for the subscriber to
avoid a false alarm transmission. This feature does not apply to zone type 9
alarms (Supervised Fire) or to 24-hour zone types 6, 7, and 8 (silent panic,
audible alarm, auxiliary alarm), which are always sent as soon as they occur.
SIA Guidelines: must be set to a minimum of 15 seconds
UL/SIA The sum of the burglary abort window entered in ✻50 and the
entry delays entered in either Field ✻35 or ✻36 should not exceed
1 minute.
Note: The control validates the data entered in this field. If the selection is
not valid the control will emit a single long beep indicating that the
selection has been rejected. The control replaces the selection with
the default value which is displayed on the keypad.
selection has been rejected. The control replaces the selection with
the default value which is displayed on the keypad.
✻
51
Periodic Test Report
0 = no test report
2 = weekly
1 = once every 24 hrs 3 = once every 30 days
Test report code entered in field
✻
64 is sent.
✻
52
First test Report Offset
0 = 24 hrs after exit program mode or download
1 = 6 hours after exit program mode or download
2 = 12 hrs after exit program mode or download
3 = 18 hrs after exit program mode or download
This is the time to first report from programming or downloading.
✻
53
Sescoa/Radionics Select
0 = Radionics (0–9, B–F reporting)
1 = SESCOA (0–9 only reporting)
Select 0 for all other formats.
✻
54
Lack of Usage Notification
0 = Disabled
4 = 90 days
1 = 1 day
5 = 180 days
2 = 7 days
6 = 365 days
3 = 27 days
Note: There will be no local annunciation indicating that
this report has been sent to the Central Station.
If enabled, notifies the central station if an end user is not operating their
security system by sending a System Inactivity report 654. The report will
be sent only to the Primary phone number and only if Contact ID® format
was selected.
Note: The report will follow the
security system by sending a System Inactivity report 654. The report will
be sent only to the Primary phone number and only if Contact ID® format
was selected.
Note: The report will follow the
✻
49 = 0 rules, no matter which selection
was made in
✻
49.