UTC Fire & Security B.V. ATS1190-1192 用户手册
The ATS1190/1192 Smart Card Readers are multifunction, all-purpose proximity card readers suitable for
all locations (including outdoors) requiring a short-range reader. The readers can be connected directly to
the Advisor Master RS485 BUS (see Figure 2). They are configurable through a menu system accessible
via the BUS or by configuration cards programmed through Titan and the Aritech Smart Card Programmer
(ATS1620).
The readers operate from 9 to 14 VDC. They have a quiescent current consumption of less than 25mA and
less than 80mA, when reading a card. The ATS1190 is supplied standard with a white removable cover,
which can be interchanged with one of four other colours available.
all locations (including outdoors) requiring a short-range reader. The readers can be connected directly to
the Advisor Master RS485 BUS (see Figure 2). They are configurable through a menu system accessible
via the BUS or by configuration cards programmed through Titan and the Aritech Smart Card Programmer
(ATS1620).
The readers operate from 9 to 14 VDC. They have a quiescent current consumption of less than 25mA and
less than 80mA, when reading a card. The ATS1190 is supplied standard with a white removable cover,
which can be interchanged with one of four other colours available.
Figure 1: Smart Card Reader
A - Blue LED:
- Door open
- Disarmed
- Disarmed
B - Comms:
- LED control
- Buzzer control
- Power
- Buzzer control
- Power
C - Red LED:
- Door open
- Armed
- Armed
The readers can be mounted on any flat surface with two 3.0-3.5 mm diameter pan-head screws. A slightly
reduced range will be experienced when mounted on metal surfaces. If mounting in an outdoor
environment, ensure that the blue LED is at the top. The use of countersunk screws is not recommended.
Remove the ATS1190 cover to expose the mounting screw by gently prying the sides away from the main
body to release the retaining clips and gently pulling on the connection cord. Do not use excessive force or
the reader can be irreparably damaged. After mounting, gently press the cover over the main body until it
locks into place.
reduced range will be experienced when mounted on metal surfaces. If mounting in an outdoor
environment, ensure that the blue LED is at the top. The use of countersunk screws is not recommended.
Remove the ATS1190 cover to expose the mounting screw by gently prying the sides away from the main
body to release the retaining clips and gently pulling on the connection cord. Do not use excessive force or
the reader can be irreparably damaged. After mounting, gently press the cover over the main body until it
locks into place.
The address of the reader for BUS operations is set to the default address, RAS 16. You can change this by
using a configuration card or accessing its on-line menu system when it is connected to the RS485 BUS.
See the Programming Guide, Reader Address, for further details.
using a configuration card or accessing its on-line menu system when it is connected to the RS485 BUS.
See the Programming Guide, Reader Address, for further details.
Figure 2: BUS Connection Block
+12 V
- Red
D–
- Green
0 V
- Black
Open collector - Violet
D+
- White
The reader is provided with a tamper facility. When connected to the BUS, tamper data is transmitted to
the Advisor Master with system data. An external Open Collector output (violet wire) can be configured as
a tamper control for both on-line and off-line operation.
the Advisor Master with system data. An external Open Collector output (violet wire) can be configured as
a tamper control for both on-line and off-line operation.
Figure 3: Wiegand Connection Block
+12 V
- Red
L2
- Brown
0 V
- Black
L1
- Yellow
D0
- Green
BZ
- Blue
D1
- White
Tamper
- Violet
Figure 4: Four-Door Controller Local Bus
+12 V
- Red
D–
- Green
0 V
- Black
RTE
- Yellow
D+
- White
Tamper
- Violet
Smart Card Reader ATS1190/1192
Installation Guide
Introduction
Mounting
RAS
Addressing
Addressing
Tamper
Comms
DWG#1190IG
Revision 4 10/02