Intermatic CA3750 用户手册
WARNING:
WARNING:
WARNING:
Read instructions completely before installation and retain for future reference.
This device is not a motor disconnect.
This device is not a motor disconnect.
with 75°C rated copper or copper clad wire.
WARNING:
WARNING:
OTHER CAUTIONS:
WARNING:
OTHER CAUTIONS:
For installation and/or use in accordance with appropriate electrical codes and regulations.
Consult a qualified electrician for installation and operation.
Consult a qualified electrician for installation and operation.
1. For remote operation, use with Z-Wave compatible control for wireless control from any location.
2. Disconnect power when servicing or changing load.
3. Use this device only
2. Disconnect power when servicing or changing load.
3. Use this device only
Note: For independent channel control requires presence of InTouch™ Server (CA5500B or other).
Model CA3750
Multi-Voltage High Current
Contactor Module
Contactor Module
Specifications:
Ratings:
Enclosure:
Connections:
RF Information:
Network Information:
Local control via Activator Button
or Wireless RF Control
or Wireless RF Control
120, 208, 240, 277VAC, 50/60Hz
6600 Watts 30 A Resistive;
5500VA 25 A Inductive;
5540 Watts 20 A @ 277VAC Ballast;
4400 Watts 20 A Tungsten;
3HP @ 220VAC Motor
6600 Watts 30 A Resistive;
5500VA 25 A Inductive;
5540 Watts 20 A @ 277VAC Ballast;
4400 Watts 20 A Tungsten;
3HP @ 220VAC Motor
NEMA 3R Indoor-Outdoor
Polycarbonate Case.
Polycarbonate Case.
1-Neutral/Line 2, 2-Line 1, 3 & 4
Contact 1, 5 & 6 Contact 2
Contact 1, 5 & 6 Contact 2
Minimum Range:
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
Mesh Network - Each line powered
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
Operating Temperature Range:
14°F (-10°C) to 140°F (60°C)
Power Consumption: 6.0W Max
14°F (-10°C) to 140°F (60°C)
Power Consumption: 6.0W Max
INSTALLATION:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
Operation:
2. Follow all local electrical and safety codes, National Electric Code (NEC), as well as Occupational Safety
and Health Act (OSHA).
3. If the power disconnect point is out of sight, lock it in the “OFF” position and tag it to prevent unexpected
application of power.
4. Move fused jumper to proper source voltage selection 120, 208, 240, or 277 VAC.
5. Set contact selector switch for desired output. (1x DPST or 2x SPST)
6. Do not exceed the maximum current carrying capacity of this contactor module.
7. Always replace the plastic insulator covering the terminal before turning power “ON”.
8.
and Health Act (OSHA).
3. If the power disconnect point is out of sight, lock it in the “OFF” position and tag it to prevent unexpected
application of power.
4. Move fused jumper to proper source voltage selection 120, 208, 240, or 277 VAC.
5. Set contact selector switch for desired output. (1x DPST or 2x SPST)
6. Do not exceed the maximum current carrying capacity of this contactor module.
7. Always replace the plastic insulator covering the terminal before turning power “ON”.
8.
Press activator button repeatedly to cycle contact operation; 2xSPST Mode: OFF:OFF,
ON:OFF; DPST Mode: OFF:OFF, ON:ON
7. For programming instructions refer to the
7. For programming instructions refer to the
(158CA12789).
InTouch Installer & Users Guide
The CA3750 Multi-Voltage High Current Contactor Module is a Z-wave™ enabled device which is
fully compatible with any Z-wave enabled network. Z-wave enabled devices display the Z-wave
logo and guarantee connectivity and interoperability between devices. Each node in a Z-wave
network is designed to act as a repeater forming a mesh network eliminating radio “dead spots”
and providing the highest level of reliability.
fully compatible with any Z-wave enabled network. Z-wave enabled devices display the Z-wave
logo and guarantee connectivity and interoperability between devices. Each node in a Z-wave
network is designed to act as a repeater forming a mesh network eliminating radio “dead spots”
and providing the highest level of reliability.
- Multiple location ON/OFF control of contactor when used with wireless controls.
- Multi-Voltage power supply 120, 208, 240, or 277 VAC
- Field configurable outputs 2 independently controllable SPST contacts or simultaneous DPST
contact operation.
- Up-front activator switch always operates load, does not require central control system.
- Multi-Voltage power supply 120, 208, 240, or 277 VAC
- Field configurable outputs 2 independently controllable SPST contacts or simultaneous DPST
contact operation.
- Up-front activator switch always operates load, does not require central control system.
Features
1
2
3
4
5
6
LINE
LINE/
NEUTRAL
Program
Button
Button
Input / Output
Terminals
Terminals
Status
LED
LED
Supply
Terminals
Terminals
ThisproductiscompatiblewithotherZ-Wave enabledproducts
™
Providing a Brighter Solution™
158CA12473
WIRELESS CONTROLS
TM