Tiinlab Acoustic Technology Co. Ltd. TWSEJ01JY 用户手册

纸张要求 折叠后75x68mm
110g无光铜 过哑油

PANTONE COOL GRAY 11C

产品介绍

小 米 蓝 牙 耳 机   A i r   使 用 说 明 书

充电接口

充电盒

耳机

功能键

指示灯

配件清单

●

 

耳机充电：

耳机放入充电盒，自动进入充电状态。

●

 

充电盒充电：

充电时指示灯慢闪，充电完成指示灯长亮。

注意：首次使用，设备为关机状态，请将耳机放入充电盒内，并按一下功能

              键激活。建议使用前先对设备进行充电。

1.  耳机放入充电盒中；

2.  长按充电盒功能键10秒以上，指示灯长亮，松开按键；

3.  耳机重新启动，旧连接记录被清除，进入重新配对模式。

1.  将耳机从充电盒取出，按照耳机左右耳标识进行佩戴。

2.  可根据自身佩戴舒适度更换合适的耳套。

3.  使用完，及时将耳机放回充电盒，以延长使用寿命及防止丢失。

使用

使用说明

●

 

连接新设备

将耳机放入充电盒中，长按功能键2秒，充电盒指示灯闪烁，耳机等待连接。

开启设备蓝牙，搜索并连接蓝牙设备“Mi True Wireless Earphones”。如需

连接密码，输入“0000”。

●

 连接两台设备

将单边耳机放入充电盒中，长按功能键2秒，使用设备A搜索并连接耳机。

将已连接设备A的单边耳机从充电盒中取出，放入另一边耳机，长按功能键2

秒，使用设备B搜索并连接耳机，即可将两个单边耳机分别连接不同设备使用。

提示：使用此功能前，需将两个单边耳机的连接记录清除。

●

 

连接中断

当设备关闭蓝牙连接或超出耳机连接范围时，耳机自动进入等待连接状态；

若10分钟内未连接到任何设备，耳机进入休眠状态，重新佩戴可唤醒，进入

等待连接状态。

●

 

自动回连

耳机在充电盒中，打开充电盒，耳机将自动回连最近连接过的蓝牙设备；若

没有检测到连接记录或无法成功回连任何蓝牙设备，耳机自动进入等待连接

状态。

提示：若耳机不能与设备自动回连，需在设备的蓝牙界面进行手动连接。

来电：

轻触两次任一侧耳机可接听/挂断电话。

音乐：

双耳佩戴：

轻触两次右耳机，可播放/暂停音乐。

轻触两次左耳机，可唤醒语音助手。

取下其中一个耳机，音乐暂停。

注意：部分手机需要在手机端打开语音助手权限。

单耳佩戴：

轻触两次耳机，可播放/暂停音乐。

主动降噪

耳机工作中，长按任一侧耳机3秒，听到提示音，开

启/关闭主动降噪功能。

提示：来电或通话中无法开启/关闭主动降噪功能。

连接

功能介绍

重置

●

 

查看耳机电量

耳机充电中，或从充电盒、耳朵中取出：

耳机指示灯长亮5秒，表示电量充足；

耳机指示灯闪烁，表示电量低，需及时充电。

●

 

查看充电盒电量

充电盒盖关闭状态，按一下功能键或打开充电盒盖：

充电盒指示灯长亮5秒，表示电量充足；

充电盒指示灯闪烁，表示电量低，需及时充电。

查看电量

打开充电盒，耳机自动开机。

开机

充电

耳机参数

2018年10月  版本1.0

小米蓝牙耳机Air产品保修说明

非保修条例

1. 未经授权的维修、误用、碰撞、疏忽、滥用、进液、事故、改 

    动、不正确的使用非本产品配件，或撕毁、涂改标贴、防伪标记；

2. 已超过三包有效期；

3. 因不可抗力造成的损坏；

4. 不符合《产品性能故障表》所列性能故障的情况；

5. 因人为原因导致本产品及其配件产生《产品性能故障表》所列性

    能故障。

服务热线：400-100-5678 

服务网址：http://www.mi.com/service

制  造  商：耳一号声学科技（深圳）有限公司（小米生态链企业）

地          址：深圳市南山区学苑大道田寮大厦（新材料产业园）东座14层

小米蓝牙耳机Air

性能故障

名称

说明书所列功能失效
喇叭无声
麦克风无声
按键功能失效
因结构或材料因素造成的主体破损

产品性能故障表

以下仅适用于中国大陆地区用户

小米蓝牙耳机Air产品售后服务严格依据《中华人民共和国消费者权益保护

法》、《中华人民共和国产品质量法》实行售后三包服务，服务内容如下：

1. 自您签收次日起7日内，本产品出现《产品性能故障表》所列性能故障的情

     况，经由小米售后服务中心检测确定，可免费享受退货或换货服务；

2. 自您签收次日起8日-15日内，本产品出现《产品性能故障表》所列性能故

     障的情况，经由小米售后服务中心检测确定，可免费享受换货或者维修服

     务；

3. 自您签收次日起12个月内，本产品出现《产品性能故障表》所列性能故障

     的情况，经由小米售后服务中心检测确定，可免费享受维修服务。

产品型号：TWSEJ01JY

产品净重：58g

充电端口：USB Type-C

喇叭阻抗：16Ω

耳机灵敏度：105dB

频响范围：20-20,000Hz 

输入参数：5V     1.1A

无线连接：蓝牙4.2

蓝牙协议：BLE/HFP/HSP/A2DP/AVRCP

工作距离：10m

充电时间：1h

耳机单次续航：3h（80%音量）

配合充电盒整体续航：10h（80%音量）

CMIIT  ID：XXXXXXXX

执行标准：Q/WMSX 002-2016

Specifications

降噪麦克风

通话麦克风

指示灯

充电盒

耳机

硅胶耳套

R

Incoming calls:

Touch the earphone on either side twice to 

answer/hang up the call.

Music:

Wearing both ears:

Touch the right earphone twice to play/pause music.

Touch the left earphone twice to wake up the voice 

assistant.

Remove one of the earphones, the music will be 

paused.

Wearing single ear:

Touch the earphone twice to play/pause music.

Note: The voice assistant needs device support and 

the voice assistant permission is enabled on the 

device.

Active Noise Cancellation

During the earphones are working, press and hold 

the headset on either side for 3 seconds, and hear 

the prompt tone to enable/disable the active noise 

cancellation function.

Note: Active noise cancellation is not available 

during calls or calls. 

Functions

USB Type-C充电线

说明书

硅胶耳套×3对

部件名称

铅

(Pb)

六价铬

(Cr(VI))

多溴联苯

（PBB）

多溴二苯醚

（PBDE）

有害物质

汞

(Hg)

镉

(Cd)

耳机线

电路板及组件

塑胶部件

金属部件

耳套

本表格依据SJ/T 11364的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
         规定的限量要求以下。
×：表示该有害物质至少在该部件的某一均质材料中的含量超出
         GB/T 26572规定的限量要求。
本产品符合欧盟RoHS2.0(2011/65/EU)环保标准。

产品中有害物质的名称及含量

Product Overview

Charging port

Charging case

Earphone

Function button

Indicator

Packing list

● 

charge the earphones

Put the earphones into the charging case and automatically enters the 

charging state.
● 

charge the charging case

If the indicator flashes slowly, it indicates that the charging case is still 

charging; if the indicator lights up, it indicates that the charging case is fully 

charged.

Note: The device is powered off for the first time. Put the earphones into the 

charging case and press the function button to activate it. It is suggested to 

charge the device before use.

How to use

● 

View battery of earphones

The following two states can be used to view the battery of earphone：

1. When the earphone is charging；

2. When the earphone is removed from the charging case and the ear.

    The headphone indicator lights up for 5 seconds, indicating that the   

    battery is fully charged; the earphone indicator flashes, indicating that  

    the battery is low and needs to be charged in time. 

   
● 

View battery of charging case

With the charging cover closed, press the function button or open the 

charging cover:

1. The charging case indicator lights up for 5 seconds, indicating that the 

    battery is fully charged;

View battery

Charging

Turning on

Clearing Connection History

●

 

Connect new device

1. Put the earphones into the charging case, press and hold the function 

    button for 2 seconds, the charging case indicator flashes, and the 

    earphones wait for connection.

2. Turn on your device Bluetooth and search for and connect to “Mi True 

     Wireless Earphones”. If a password is required, enter "0000".

● 

Connect two devices

1. Put the single-sided earphone into the charging case, press and hold the    

    function button for 2 seconds, use device A to search and connect the 

    earphone.

2. Take the single-sided earphone of connected device A from the charging 

     case, put the other side of the earphone into the charging case, press 

     and hold the function button for 2 seconds, use device B to search and 

     connect the earphone, then connect the two single-sided earphones to 

     different devices.

 

Tip: Before using this function, you need to clear the connection records of 

the two single-sided headphones. 

Connecting

Open the cover of the charging case, the earphones will automatically turn on.

2. The charging case indicator flashes, indicating that the battery is low and 

     needs to be charged in time.

●

 

Connection Lost

When the device turns off Bluetooth feature or is out of wireless range, the 

earphones will enter standby mode. If connection is not restored within 10 

minutes, the earphones enter the sleep state, re-wearing can make up and 

enter standby mode.

● 

Reconnecting

Open the charging case (with earphones inside), the earphones will 

reconnect to your previous device automatically. If there is no connection 

record or any Bluetooth device cannot be successfully connected, the 

earphones automatically enter standby mode.

1. Put the earphones into the charging case.

2. Press and hold function button for more than 10 seconds, the indicator  

    turns on, then release the button.

3. The earphones reboot and the old connection record is cleared and 

    enter the re-pairing mode.

Noise cancellation 

microphone

Voice call 

microphone

Indicator

Charging case

Earphone

Silicone eartips

R

USB Type-C 

charging cable

User Manual

silicone eartips × 3 pairs

Model: TWSEJ01JY

Weight: 58 g

Charging port: USB Type-C

Impedance: 16 Ω

Sensitivity: 105 dB

Frequency response: 20-20,000 Hz

Input: 5 V     1.1 A

Wireless connectivity: Bluetooth 4.2

Bluetooth profiles: BLE/HFP/HSP/A2DP/AVRCP

Wireless range: 10 m

Charging time: 1 h

Battery life of single charge: 3 h (80% volume)

Battery life with charging case: 10 h (80% volume)

CE

Hereby,Tiinlab declares that the radio equipment type Mi True Wireless 

Earphones is in compliance with Directive 2014/53/EU. The full text of the EU 

declaration of conformity is available at the following internet address: 

https://www.mi.com/en/service/support/declaration.html

Note：

Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the

device in these environments may result in circuit malfunctions.

• Use the device at temperatures between –10°C and 55°C, and store the 

device and its accessories at temperatures between –40°C and 70°C. 

Extreme heat or cold may damage the device. At temperatures below 5°C, 

the performance of the battery will be degraded.

• Do not place the device in places that are easily exposed to direct 

sunlight such as on a car dashboard or on a window sill.

• Keep your device away from appliances with strong magnetic or 

electrical fields, such as microwave ovens and refrigerators.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to 

the following two conditions: (1) this device may not cause harmful 

interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate the 

equipment.

This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not 

occur in a particular installation.

If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of 

the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.