ICOM 386400 用户手册

viii

PRECAUTIONS

DANGER HIGH RF VOLTAGE! NEVER touch an

antenna or antenna connector while transmitting. This could

cause an electrical shock or burn.

DANGER! NEVER operate the transceiver near

unshielded electrical blasting caps or in an explosive

atmosphere. This could cause an explosion and death.

WARNING RF EXPOSURE! This device emits Radio

Frequency (RF) energy. Extreme caution should be

observed when operating this device. If you have any

questions regarding RF exposure and safety standards

please refer to the Federal Communications Commission

Office of Engineering and Technology’s report on

Evaluating Compliance with FCC Guidelines for Human

Radio Frequency Electromagnetic Fields (OET Bulletin 65).

WARNING! NEVER operate the transceiver with a

headset or other audio accessories at high volume levels. If

you experience a ringing in your ears, reduce the volume or

discontinue use.

WARNING! NEVER apply AC power to the [DC13.8V]

socket on the transceiver rear panel. This could cause a fire

or damage the transceiver.

WARNING! NEVER apply more than 16 V DC to the

[DC13.8V] socket on the transceiver rear panel. This could

cause a fire or damage the transceiver.

WARNING! NEVER reverse the DC power cable

polarity. This could cause a fire or damage the transceiver.

WARNING! NEVER remove the fuse holder on the DC

power cable. Excessive current caused by a short could

cause a fire or damage the transceiver.

WARNING! NEVER let metal, wire or other objects

contact the inside of the transceiver, or make incorrect

contact with connectors on the rear panel. This could cause

an electric shock or damage the transceiver.

WARNING! NEVER operate or touch the transceiver

with wet hands. This could cause an electric shock or

damage to the transceiver.

WARNING! NEVER operate the equipment if you notice

an abnormal odor, sound or smoke. Immediately turn OFF

the power and/or remove the DC power cable. Contact your

Icom dealer or distributor for advice.

WARNING! NEVER put the transceiver on an unstable

place where the transceiver may suddenly move or fall.

This could cause an injury or damage the transceiver.

WARNING! NEVER operate the transceiver during a

lightning storm. It may result in an electric shock, cause

a fire or damage the transceiver. Always disconnect the

power source and antenna before a storm.

CAUTION: DO NOT expose the transceiver to rain, snow

or any liquids. They could damage the transceiver.

CAUTION: DO NOT change the internal settings of the

transceiver. This may reduce transceiver performance and/

or damage the transceiver. The transceiver warranty does

not cover any problems caused by unauthorized internal

adjustments.

CAUTION: DO NOT install the equipment in a place

without adequate ventilation, or block any cooling vents

on the top, rear, sides or bottom of the transceiver or the

cooling fan. Heat dissipation may be reduced and damage

the transceiver.

CAUTION: DO NOT use harsh solvents such as benzine or

alcohol when cleaning. This could damage the equipment

surfaces. If the surface becomes dusty or dirty, wipe it clean

with a soft, dry cloth.

CAUTION: DO NOT place or leave the transceiver in

areas with temperatures below 0°C (32°F) or above 50°C

(122°F).

CAUTION: DO NOT place the transceiver in excessively

dusty environments, or in direct sunlight. This could

damage the transceiver.

CAUTION: DO NOT set the transceiver’s RF output power

to more than a connected linear amplifier’s maximum input

level. Otherwise, the linear amplifier will be damaged.

CAUTION: DO NOT use non-Icom microphones. Other

microphones have different pin assignments and may

damage the transceiver.

BE CAREFUL! The transceiver will become hot when

operating the transceiver continuously for long periods of

time.

NEVER leave the transceiver in an insecure place to avoid

use by unauthorized persons.

Turn OFF the transceiver’s power and disconnect the DC

power cable when you will not use the transceiver for long

period of time.

The LCD display may have cosmetic imperfections

that appear as small dark or light spots. This is not a

malfunction or defect, but a normal characteristic of LCD

displays.