Farsun Photoelectric Science Technologies co. LTD FG2106 用户手册

3 .Bluetooth communication parameter settings

When the scanner is set too much,you can scan

"Return to default" settings for Bluetooth

recovery settings code to allow the scanner to

resume factory settings.

①.Bluetooth restore the default Settings

Return to default

②.Bluetooth scanner and receiver matching method

Pair Code

③.Sleep mode

Scanner can scan the following Settings,to set up

all kinds of sleep time.To extend battery

life,Suggest that sleep time shoulds not be set too

long.

Sleep time 60 Seconds

Sleep time 2 Minutes

Sleep time 10 Minutes

④.Normal Mode

Normal mode ：Scan barcodes directly then the

decoded data transfer to the receiver and

displayed on the PC or your host ,But if the

transmission fails (for example, over the

transmission distance or the receiver is not open),

then issue "di da " sound prompts the user to

transmission failure.

Normal Mode

⑤. Inventory mode

When the scanner is not in the receiver's operating

range, please use the Inventory mode First you can

set up the mode "Inventory mode" then you scan the

barcodes ,the data will be stored in the scanner.

Inventory mode

Note:When using "Inventory Mode",the user need to

scan the clear data set code will scanner memory

empty.

Transfer data

Total Number of data

Clear data

4.Bluetooth scanner auxiliary functions

Bluetooth keyboard is fast

⑥.Wired model

2 .Bluetooth barcode scanner performance parameters

Communication distance: Indoor 7~10m

Communication protocol: Bluetooth 3.0

Compatibility: iOS,Mac,Android,XP,Win7 etc.

Data memory: 4096Byte Flash

Scanning type: manual single scan/continuous

scanning/automatic scanning

Source: LED（622nm-628nm）

The maximum scanning speed: 200 times/sec

Decoding accuracy: more than 3.3mil

Depth of focus：3.3mil:2mm-100mm

10mil:2mm-350mm

15mil:5mm-500mm

30mil:10mm-800mm

Decoding IC: 32bit high-speed processor

PCS ：The minimum reflectivity of 30%

working current: Decoding the current 40mA,working

current 20mA,Standby current 5mA,shutdown current

18uA,Internal constant current constant voltage

charging,Support while charging work.

Charging source: 5V 500mA.

Charging time: 1.5 hour.

Service time: 30 hour.

Scan Mode: Two-way single.

prompting mode：Buzzer + light

Error rate: 1 / 5000000

Scanning angle: rotation angle±30°, Oblique Angle

±45°, deflecting angle ±60°.

Decoding ability: UPC-A, UPC-E, EAN-8, EAN-13,

Code 128, Code 39, Code 39 Full ASCII,

Codabar/NW7, Code 93, Code 11, MSI, Interleaved 25,

Industrical 25, ISBN, ISSN, China Post etc.Domestic

general one-dimensional codes.

Support interface : USB HID, USB Virtual Serial(Need

to drive and setup code please contact the dealer)

The seismic test：Many times from 1.5 meters height

fell to the ground of concrete can still work

normally after impact.

Authentication：CE,FCC,RoHS,ClassI

Bluetooth barcode scanner characteristics

*.Wireless operation, convenient to carry, using

flexible workplaces;

*.Power rechargeable, can also transmit data,

using a shortcut;

*.With fine ability to decode;

*.Key is comfortable, life one million times;

*.Storage mode support extreme distance work;

*.750mAh Large capacity lithium battery,

persistent work;

*.Support Windows XP, Win 7,Androld,iOS,Mac

Packing detail: a scanner, a receiver, a USB

charging line, a simple description.

1 .Bluetooth barcode scanner overview

Product appearance figure

Barcode read correctly

When you use the USB cable ,the scanner will

change the wireless mode into wired mode .

You also can close the wire mode ，please scan the

follow barcode.

Wired mode Off

4/7

2/7

3/7

1/7

Bluetooth barcode scanner operation points for attention

①.Take out the receiver,Plugged into PC(POS)USB

Interface,After waiting for the computer to

install the driver(About 3 to 5 seconds, need

not operation, the computer automatically),The

mouse cursor in the need to enter the barcode in

the text box,You can scan you need to enter the

bar code.

②.Cable model methods of use：Plugged into

PC(POS)USB Interface,immediate use.

③.General fault repair methods：The USB

receiver to plug,Then scan"Defalut"setting.

The scanner needs and receiver after the match,Can be used

normally.To match the receiver insert a computer USB

interface,After waiting for it into the working state,By

scanner scan "Pair Code"Settings,At this point, the red and

blue lights flashing, said in the matching state, the

automatic search the bluetooth devices around, when the

buzzer sends out "di di" sound, light blue, said the match

is successful, can transmit dataAfter finishing the

matching,Scan version information Settings to observe

whether a match,If success shows version

information,Otherwise the match fails,need to match.

Short Range

Medium Range

Bluetooth reliability setting,High reliability,

Transmission distance near;Low reliability,

Transmission distance far.

①.Reliability settings

②.Matching settings

Removal of match

Disconnect the existing

Connect the host matches

Shutdown

③.Transmission speed settings

SPP Mode

④.Transmission mode settings

Automatic ON

⑤.Automatic settings

⑥.iOS keyboard show/hide Settings

Show/hide the iOS keyboard

Fast

Medium

<Slow>

（Note：Automatic function optional,Default

single mode.If need to open Automatic mode,you

can hold down the switch 8 seconds,Can switch to

the Automatic mode,If you need to shut down

Automatic mode that the same operation）

Double click the button quickly to turn on /off

the IOS keyboard ,when you have no manual book .

Transmission speed settings(Inventory mode only)