Techem Energy Services GmbH MOD5TX 用户手册
Important information
Target group
These installation instructions are intended for Techem trained
personnel. We do not mention any elementary job steps.
personnel. We do not mention any elementary job steps.
Intended use
The Mod5 meter transmitter is used for upgrading the
Techem S-30D-Vario 3 water meters to radio.
Techem S-30D-Vario 3 water meters to radio.
Safety and hazard information
As supplied, the Mod5 meter transmitter has an integral battery
whose capacity is enough for the intended period of use. – It is
not necessary to change the battery and it is also not
permitted.
whose capacity is enough for the intended period of use. – It is
not necessary to change the battery and it is also not
permitted.
Delivery, transport and storage
Scope of delivery
The standard delivery of the product contains:
• the installation instructions with conformity
declaration,
• one (1) Mod5 meter transmitter
• the installation instructions with conformity
declaration,
• one (1) Mod5 meter transmitter
Transport
The Mod5 meter transmitter must not be subjected to blows,
shocks, shaking or vibration. Transport should therefore be in
the original packaging if possible, or in another suitable
packaging.
shocks, shaking or vibration. Transport should therefore be in
the original packaging if possible, or in another suitable
packaging.
Storage
The following storage conditions must be adhered to
without exception: max. temperature: + 50 °C / min.
temperature: - 20 °C.
without exception: max. temperature: + 50 °C / min.
temperature: - 20 °C.
Techem Water Services Inc.
5661 Airport Blvd.
Boulder, CO 80301
www.techem.com
5661 Airport Blvd.
Boulder, CO 80301
www.techem.com
Mod5 meter transmitter
Mod5 meter transmitter (Art. No. xxxxxxxxxx)
ASSEMBLY INSTRUCTIONS
Sealing ring
Mod5 meter transmitter
S-30D-Vario3 meter
Installation
Retooling of S-30D-Vario3 meter to radio
1 If present: break open the ring seal on the meter
casing and detach it. To do this, pass a screwdriver blade
into one of the openings of the ring seal and twist to one
side.
2 Remove the front cap from the meter casing.
casing and detach it. To do this, pass a screwdriver blade
into one of the openings of the ring seal and twist to one
side.
2 Remove the front cap from the meter casing.
The area of the meter casing where the Mod5 meter transmitter
makes contact must be clean and dry – especially in the area of
the ring seal. If necessary, clean this area with water and dry it. If
this is still not enough, the meter casing must be changed.
makes contact must be clean and dry – especially in the area of
the ring seal. If necessary, clean this area with water and dry it. If
this is still not enough, the meter casing must be changed.
3 Apply the Mod5 meter transmitter to the meter and
allow it to click into place.
allow it to click into place.
4 Lock the connection of the Mod5 meter transmitter to
the meter casing using a ring seal.
the meter casing using a ring seal.
5 Finish the retooling with optical head and PDA.
NOTE
Changes or modifications made to this equipment not
expressly approved by Techem Water Services may void
the FCC authorization to operate this equipment.
expressly approved by Techem Water Services may void
the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment is assumed to cause
harmful interference to radio or television reception, consult
the local Techem representative.
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment is assumed to cause
harmful interference to radio or television reception, consult
the local Techem representative.