SHANGHAI ETIGER DIGITAL TECHNOLOGY CO. LTD. ES-D1A 用户手册

Box Content

1 x PIR Motion Detector

1 x Bracket

1 x User Manual

1. Detection window

2. LED indicator

3. Bracket

Before Using for the First Time

Open the case and remove the battery activation strip to activate the

batteries. Self-testing starts for 30 seconds.

www.etiger.com

ES-D1A

Wireless Motion Detector

Installation

Fix the bracket on the wall with screws and attach the detector to the

bracket. Adjust the bracket to change the detection distance and angle.

It is recommended to mount the detector 2m from the ground.

Avoid mounting the detector close to windows, air conditioner, heater,

refrigerator, oven, sunshine and places where the temperature changes fast

or where the air stream flows frequently.

If two detectors are installed in the same detection scope, adjust the

location to avoid interferences and false alarms.

The detector is more sensitive to cross movements than vertical movements.

Top view

Side view

Detection scope

PCB Layout

Jumpers for Zone setup

Tamper switch

Infrared sensor

AA 1.5V LR6

Antenna

LED working indicator

Infrared sensor: Detects the infrared rays released by human body

motion. Do not touch the surface. Keep the surface clean.

Tamper switch: When the alarm system is armed, the tamper switch

will trigger the alarm if the case is opened.

Jumpers for Zone setup: The jumpers enable you to assign the

detector to a specific zone. Refer to the user manual of your alarm

system for more information on zone set up.

Mode Setting

Testing mode

Once the self-testing is complete, long press the test button. The sensor

switches to testing mode, and scans once every 10 seconds. After 3

minutes, the LED blinks twice, and the sensor switches to working

mode.

Working mode / Stand-by mode

In working mode, if the sensor is triggered more than twice within 3

minutes, it will switch to standby mode to save power. If no movement

is detected within the next 3 minutes, the sensor goes back to working

mode.

Register the detector in the alarm system

Switch to Connection Mode on the control

panel. Press the test button of the sensor

twice. The control panel beeps once: the

motion detector is registered. If you hear

two beeps, the detector has already been

connected.

To check if the registration is complete, arm

the system and trigger the sensor again.

If the siren rings out, the registration is

successful.

Test

Button

Specifications

Power Supply:

DC 3V (AA 1.5V LR6 x2)

Static current:

≤90uA

Transmitting current:

≤9.5mA

Transmission distance:

≤ 80 m (in open area)

Radio-frequency:

315MHz (±75KHz)

Housing material:

ABS plastic

Operating conditions:

Temperature: -10°C ~ +55°C

Relative Humidity: ≤80% (non-con-

densing)

Detector dimensions:

107 x 53 x 32 mm

Bracket dimensions:

52 x 30 x 26.5 mm

LED indications

Blinks continuously: Self-testing

Blinks once: An intruder is detected

Blinks twice: Self-testing is complete; entering working mode.

Blinks 3 times every 3 seconds: Under-voltage indication: the batteries

must be replaced (the user will be informed by SMS when the batteries

are low if the detector is registered in the control panel).

Standards

This product bears the selective sorting symbol for waste electrical

and electronic equipment (WEEE). This means that this product must

be handled pursuant to European Directive 2002/96/EC in order to be

recycled or dismantled to minimize its impact on the environment. For

further information, please contact your local or regional authorities.

Electronic products not included in the selective sorting process are

potentially dangerous for the environment and human health due to

the presence of hazardous substances.

In compliance with European laws.

This product was designed and manufactured in compliance with

Directive 2002/95/EC of the European Parliament and of the Council on

the restriction of use of certain hazardous substances in electrical and

electronic equipment (RoHS Directive - RoHS) and is deemed to comply

with the maximum concentration values set by the European Technical

Adaptation Committee (TAC).

Manufactured in China.

Images, illustrations and text are non-contractual. ETIGER and the ETIGER logo are

registered trademarks and the property of ETIGER.

ETIGER EUROPE

Rue de la Loi, 25, 7100 La Louvière, Belgique

service@etiger.com

-D1A

-UM

-EN20140724-1.1-

This user manual is available in other languages at