Yuneec Technology Co. Limited CGO3 用户手册
CGO3 USER MANUAL
INTRODUCTION
CGO3 (available separately) is an innovative combination of 3-axis brushless
gimbal, camera and digital video downlink.
The Self-Stabilizing gimbal makes it possible to capture amazing photographs and
video footage for an array of uses. And the built-in digital video link delivers
streaming video to 5.8GHz WiFi compatible iOS® and Android™ equipped devices
including smart-phones and tablets as well as YUNEEC Personal Ground Stations.
OPERATING INSTRUCTIONS:
(1) Insert the micro SD card into CGO3, plug in the power cord and slide the power switch, then
CGO3 start to work;
(2) When the green light starts to flash , it indicates that wifi has started to work. At this time, you
can take device to connect to CGO3's wifi, when the device is connected, the light will grow
solid green.
(3) Then press the shutter button, CGO3 will take a picture; long press the shutter button, CGO3
will enter recording function;
(4) Toggle the switch ,then CGO3 will be powered off.
OPERATION:
(1) Plug the 3-Pin power cord into the appropriate socket head.
(2) Install the gimbal under the belly of plane.
(3) Power on the plane, then gimbal will work.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is con-
nected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two condi-
tions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the party responsible for com-
CAUTION: Any changes or modifications not expressly approved by the party responsible for com-
pliance could void the user's authority to operate this equipment.
RF EXPOSURE WARNING
• This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired opera-
tion of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled
environment.
Cet équipement respecte les limites d'exposition aux rayonnements IC définies pour un environne-
ment non contrôlé