Extron Electronics EXTWAP100AC 用户手册
ATTENTION:
•
The length of the exposed wires in the stripping process is critical. The ideal
length is 3/16 inches (5 mm). If they are any longer, the exposed wires may touch,
causing a short circuit between them. If they are any shorter, the wires can be
easily pulled out even if tightly fastened by the captive screws.
length is 3/16 inches (5 mm). If they are any longer, the exposed wires may touch,
causing a short circuit between them. If they are any shorter, the wires can be
easily pulled out even if tightly fastened by the captive screws.
•
La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5 mm (3/16 inches). S’ils sont un peu plus longs,
les câbles exposés pourraient se toucher et provoquer un
dénuder. La longueur idéale est de 5 mm (3/16 inches). S’ils sont un peu plus longs,
les câbles exposés pourraient se toucher et provoquer un
court circuit. S’ils sont un
peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.
•
Do not tin the wire leads before installing into the connector. Tinned wires are not
as secure in the connector and could be pulled out.
as secure in the connector and could be pulled out.
•
Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
Mounting holes
Cable guide
Kensington security
lock
lock
C
Mounting holes
(2) (see page 4)
— Used to mount the unit to a wall or ceiling (see
Mounting on
page ).
D
E
Kensington security lock
— For added security, attach a Kensington Security Lock
(not
provided) to the metal-reinforced slot on the top of the unit.
Follow the instructions that are provided by the manufacturer to install the lock.
WAP 100AC Bottom Panel Features
These features provide diagnostic tools that can be used for troubleshooting. The LEDs can
be activated or inactivated within the WAP 100AC web pages.
be activated or inactivated within the WAP 100AC web pages.
A
This needs a new Photo
from Marketing so that it
says “Extron.”
from Marketing so that it
says “Extron.”
B C D E F
On page 9 of the EnGenius
user guide, it says this.
However, on page 58, the
software has a “Reset”
button that reboots the
device. I’m assuming that
these are different functions.
On page 51, the software has
another “Reset” button that
seems to have the same
function as the physical
reset button.
user guide, it says this.
However, on page 58, the
software has a “Reset”
button that reboots the
device. I’m assuming that
these are different functions.
On page 51, the software has
another “Reset” button that
seems to have the same
function as the physical
reset button.
Figure 3.
WAP 100AC Bottom Panel
A
Reset button
— resets all user settings and reverts back to the factory default state. To
carry
out this reset, press the reset
button for over 10 seconds.
button for over 10 seconds.
B
C
WLAN 5G LED
— indicates that the 5 GHz frequency is in use (IEEE
standard
802.11a, b, g, n,ac).
D
WLAN 2.4G LED
— indicates that the 2.4 GHz frequency is in
use
(IEEE standard 802.11a, b, g, n,ac).
E
Ethernet Port LED
— indicates that the unit is connected to a network.
F
Power LED
— indicates that the unit is receiving power.
WAP 100AC • Panel Features
8
WPS LED
— indicates Wi-Fi Protected Setup is enabled.
Cable guide
— Ensures cables for power and network connections do not get damaged.