Shenzhen Guiyuan Industry Development Co. Ltd. CARYMART-CWB4 用户手册
RF Wireless Remote Receiver &Transmitter Model (S4C-DC12 & CWB-4)
Feature:
Wireless control, easy to install
Relay output, can control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110~240V or
DC0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Receiver:
Model No.: S4C-DC12
Power Supply (Operating Voltage): DC12V±1V
Working Frequency: 315MHz
Channel: 4 CH
Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Maximum Working Current of Relay: 5A / each channel
Static Current: ≤6mA
PCB Size: 68mm x 48mm x 20mm
Case Size: 75mm x 55mm x 30mm
Work with Fixed code transmitters or Learning code transmitters.
The receiver can pair different model transmitters, includes model CWB-4(50M), C-4(100M), CV-4 (500M), CP-4 (500M) and CB-4 (1000M) etc...
If you want to have a further working range, you can install an external antenna to the receiver, such as magnetic mount antenna (model
0020909), which working range is three times as much as it used to be. Or telescopic antenna (model 0020908), which working range is twice as
much as it used to be.
Transmitter:
Model No.: 0021095 (CWB-4)
Waterproof
Shell Color: Black
Channel/Button: 4
Button Symbol: A, B, C, D
Operating Voltage: 6V (2 x CR2016 -3V button cell batteries,, can be used for 12 months)
Operating Current: 5mA
Operating Frequency: 315Mhz
Encoding Chip: LX2260
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 50m / 150ft (theoretically)
The distance of 50m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be
hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or
may not reach 50m.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 56mm x 32mm x 12mm
Weight: 20g
Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “H” side, and the lower row of pads is “L” side.
3. If solder the middle row of chip feet to the “L” side, it is code 1. If solder the middle row of chip feet to the “H” side, it is code 2. Don’t solder to
The distance of 50m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be
hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or
may not reach 50m.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 56mm x 32mm x 12mm
Weight: 20g
Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “H” side, and the lower row of pads is “L” side.
3. If solder the middle row of chip feet to the “L” side, it is code 1. If solder the middle row of chip feet to the “H” side, it is code 2. Don’t solder to
any side, it is code 0.
4. The 8-bits code order is from right to left (from D1 to D8).
5. Here is an example, the 8-bits code in the picture is 00001020, solder as the following way:
6. Code 0: don’t solder any side, like D1, D2, D3, D4, D6, D8.
7. Code 1: solder to the “L” side, like D5.
8. Code 2: solder to the “H” side, like D7.
How to pair the transmitter to the receiver:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
5. Here is an example, the 8-bits code in the picture is 00001020, solder as the following way:
6. Code 0: don’t solder any side, like D1, D2, D3, D4, D6, D8.
7. Code 1: solder to the “L” side, like D5.
8. Code 2: solder to the “H” side, like D7.
How to pair the transmitter to the receiver:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.