Reliance Worldwide Corporation UFMT1000 用户手册

For questions, troubleshooting and assistance, contact

support@soneter.com

Welcome to your Smart Home

Water S

ystem

A new way to conserve and pr

otect

SMARTFLOWH20

INSTALL GUIDE

Used for pipe calibration

or restoring factory settings.

Meet Your Smart W

ater meter

meter features

Push Button

Guides the zip ties that are used to secur

e the meter on the pipe.

Zip Tie Channels

Accepts the included AC power cord

to provide power to the meter

Power Connector

blue led

sensors

Indicates wireless connectivity

and pairing status and events.

Indicates pipe calibration status or if

there is pr

oper signal through the pipe.

Green LED

Underside of Meter

Allows ultrasonic signals to enter the pipe.

install ma

terials

Removes dirt, dust and particles from the pipe.

You can deter

mine your pipe size by wrapping

the cloth end to end around the pipe; if it

touches then the pipe is 3/4’’, if not then it is 1’

’.

Your meter must be installed wher

e an outlet

is accessible either directly or via extension

cord (not included).

Power supply

Emery Cloth

Grease allows the ultrasonic signal to pass

through the pipe. If ther

e is too little or too

much grease covering the sensors, no r

eadings

will occur. Use as dir

ected.

Wash your hands thor

oughly after

completing the installation. You may want to keep

some paper towels nearby while installing the monitor.

Grease Applicator

Skin Contact

Use two zip ties to secure the monitor to the

pipe via the Zip Tie Channels. The zip ties must

be as tight as possible; loose zip ties will cause

the signal to be weak.

Zip Ties

learn. monitor. protect.

Know your water like never before.

Additional Information, Warnings, and Certifications

Industry Canada Regulations:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans

le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le

type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Federal Communications Commissions Regulations:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures: —Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/

TV technician for help.

15.19(a)(3): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Additional Information, Warnings, and Certifications

Industry Canada Regulations:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to

other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de

réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne

et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire

à l'établissement d'une communication satisfaisante.

Cet équipement est conforme aux limites d'exposition aux radiations ICES définies pour un environnement non

contrôlé . Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et une

partie de votre corps

Federal Communications Commissions Regulations:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult

the dealer or an experienced radio/ TV technician for help.

15.19(a)(3): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE

USER’S AUTHORITY TO OPERATE THE EQUIPMENT

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of

your body.