Kum Oh Electronics Co. Ltd. KSC100G2 用户手册

m1

m2

m3

m3

b

Remove the protective film

Connect the connector of security sensor cable(      ) to the connector at the bottom

surface of the cradle(      ) and insert it into the hole at the bottom surface of the

cradle.    

※Connect it while paying attention to the connector direction.

Insert the security sensor cable(      ) mold groove into the cable mold guide on the

cradle correctly and remove the protective film from the double-sided tapes on the

bottom surface of the cradle(      ).

c

c

a

a

a

G028_EN1612_R01

▶Before installing, Please check up the parts.

▶Installation Guide - Gear S2 (3G/BT) /classic - Normal Security Set(Redesign)

▶ Security sensor installation method of Gear S2 3G and Gear S2 classic
※ The installation for Gear S2 3G and Gear S2 classic is the same.

b

b

■

 Assembling flow

c

c

c

d

e

f

h

i

j

g

a

a

b

Loosen the Gear S2 screw in the direction to the strap buckle counterclockwise

using the screw driver included in the package.

※Make sure to removed the screw in the strap buckle direction of Gear S2.
※Keep the removed screw not to lose it.

Assemble the security sensor(      ) with Gear S2 while paying attention to the

assembling direction. After assembling the security sensor correctly, fix the Gear S2

and the security sensor by rotating the 8 mm screw(      )to clockwise direction.

※Ensure to use the screw(8 mm) included in the package for fixing the security sensor.

If the angle of screw driver(      ) is not stayed in 90 degrees, It can cause some

scratches on the surface of the Gear S2 or abrasion on the top of the screws.

After checking the ‘Y’ type of screws and driver, be sure to be fitted with driver(       ) an

screw. When you disassemble the screw, it needs to be applied force downward by

hand, then rotate driver counterclockwise slowly until the screw is disassembled

completely.

When you rotate driver counterclockwise, please be careful not to occur scratch or flaws

by contact the surface of Gear S2 with driver.

c

1.After removing the protective film from the double-sided adhesive tape, preserve the

   tape so that it doesn't get dirty.

   

If touching the tape with a hand or foreign materials get on it, its adhesive strength

   can be significantly deteriorated.

2.The adhesive tape will have full adhesive strength after the 24 hours from its placement.

   Please do not use the products right after its placement.

- Cautions when attaching the double-sided tape.

Insert the Charging & security cable(      ) into the hole on the smart table

while facing downward, and attach the cradle over the hole on the table. 

Array the Charging & security cable(      ) into the cable guide of the cradle

properly, insert it into the hole on the table in the direction to the rear side of

the cradle and attach it on the proper position firmly.

a

a

- S2 BT(S2 Bluetooth)

- S2 3G(S2 3G)

- S2 classic

  (classic Bluetooth)

3 kinds of security cables are included in this package.
Cable for 

Gear S2 Bluetooth (1EA), Cable for Gear S2 3G (1EA),

and Cable for

The security sensor cable model can be identified by the label
attached to the plastic bag or the imprinted text on the bottom
surface of the sensor.

c

a

Cable mold groove

Cable mold

guide

Rotate

counterclockwise

b

b

g1

g2

g3

g3

m4

g3

Hole on the

bottom surface

O

O

g3

Rotate

clockwise

h

i

j

d

d

d

d

Maintenance kit

Hole on the

smart table

Hole on the 

normal table

Position of screws

to be removed

Special ‘Y’ screw

Screw driver(       ) for ‘Y’ screw

d

※ When you disassembling the screws, please proceed in accordance with below two guidelines.

Gear S2

Screw

c

Security sensor cable

for

Gear S2 3G - Side view

Thickness 

Security sensor cable

for

Gear S2 BT - Side view

Thickness 

Security sensor cable

for

Gear S2 classic - Side view

Thickness 

Security sensor cable

for

Gear S2 classic - Side view

Thickness