Transition Networks C4TEF1013-125 产品宣传页
Point System™
Ordering Information
C4TEF1011-125
1300nm multimode (ST)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1013-125
1300nm multimode (SC)
[2 km/1.2 mi.] Link Budget: 11.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1014-125
1310nm single mode (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1015-125
1310nm single mode (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1016-125
1310nm single mode (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1017-125
1550nm single mode (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
C4TEF1035-125
1550nm single mode (SC)
[120 km/74.6 mi.] Link Budget: 36.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
*C4TEF1040-125
1 SFP port (Empty)
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
*C4TEF1040-145
2 SFP ports (Empty)
to
(4) RJ-48
[1.5 km/0.9 mi.]
plus 10/100BASE-TX (RJ-45)
[100m]
Single Fiber Products
Recommended use in pairs
C4TEF1029-125
1310nm TX/1550nm RX single fiber SM
(SC)
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
C4TEF1029-126
1550nm TX/1310nm RX single fiber SM
(SC)
[20 km/12.4 mi.] LB: 19.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
C4TEF1029-127
1310nm TX/1550nm RX single fiber SM
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
C4TEF1029-128
1550nm TX/1310nm RX single fiber SM
(SC)
[40 km/24.9 mi.] LB: 25.0 dB
to
(4) RJ-48
[1.5 km/0.9 mi.]
Specifications
Standards
Ethernet interface:
IEEE 802.3™-2008
TDM interfaces:
ANSI T1.102, T1.403 and T1.408
ITU I.431, G.703,G.736, G.775 and G.823
ETSI 300-166, 300-233 and TBR 12/13
AT&T Pub 62411
Switches
Numerous switch settings for line coding, line buildout, loopback
(per port), AIS setting, Ethernet port settings: Auto-Negotiation,
Force speed/duplex and enable Transparent Link Pass Through
Jumper
Hardware: mode is determined by DIP switch settings
Software: mode is controlled by the most recently saved,
on-board microprocessor setting
Dimensions
Width: 1.72” [44 mm]
Depth: 5.0” [127 mm]
Height: 3.4” [86 mm]
Power Consumption
3.6 Watts
Environment
See chassis specifications
Shipping Weight
1 lb. [0.45 kg]
Regulatory Compliance
EN55022 Class A, EN55024, CE mark
Warranty
Lifetime
C4TEF10xx-125
C4TEF10xx-125
point system™ slide-in-module network interface device
4x T1/E1/J1 + 10/100 Ethernet Copper to Fiber Transport Mux
see also:
Stand-Alone NID
4x T1/E1/J1 + 10/100 Ethernet Transport Mux
4
Low cost transport capability: (4) T1/E1/J1
and (1) Ethernet
4
Target applications include: FTTx, such as Fiber-to-the-
Business, Fiber-to-the-Building, Fiber-to-the-MDU,
Fiber-to-the-Home and Cell tower backhaul.
4
Copper connections compatible with G.703,
AMI/B8ZS/HDB3, 10/100BASE-TX, and RS232 channel;
while the optical connection runs at 155Mbps.
4
TDM traffic is not mapped to Ethernet. A hardware-
based solution guarantees the constant bit rate of TDM
transport without requiring traffic management.
Provides physical layer status monitoring and alarm
classification functions for Telecom operators to
manage their fiber optic network and reduce
operation and maintenance costs.
*Note: C4TEF cards cannot be used with the 1-Slot Point System™ Chassis .
Devices must be used in
pairs. Typical installation will include a chassis card installed in the Point System™
locally and a stand-alone device [S4TEF] installed at the remote location.
locally and a stand-alone device [S4TEF] installed at the remote location.
Features
4
Loopbacks via Test Set
4
Auto-Negotiation for
10/100BASE-TX
4
AutoCross™ (auto MDI/MDI-X)
[
4
Transparent Link Pass Through
for Ethernet
4
Automatic Link Restoration
4
Pause (Flow Control)
4
Remote Management
4
Local and Remote Loopback
4
Remote Fiber Loss Signaling
4
AIS/TAOS
4
LEDs for each data port
4
Settings for line code, line length,
local loopback or remote loopback
4
T1/E1/J1 mode settings
4
Local (AUX) Management Interface
4
Access to complete status
information on local and remote
device
4
Field Upgradeable Firmware
Management Features
4
Report local device status:
• Port Status
• Device settings & configuration
4
Local command operations include:
• Loopback Fiber & T1/E1
per channel
• AIS TX on fiber on loss of copper
link & AIS TX on copper on loss
of fiber link
• Ethernet settings:
• Auto-Negotiation Enable/Disable
• Force speeds and modes on
10/100TX
4
Remote device status:
• Port Status
• Device settings & configuration
4
Remote Commands:
• Loopback Fiber & T1/E1
per channel
• AIS TX on fiber on loss of copper
link & AIS TX on copper on
loss of
fiber link
• Ethernet settings
(Software Mode)
• Force speeds and modes on
10/100TX
• Enable/Disable: Auto-
Negotiation;
Link Pass Through; Flow
Control; & AutoCross™
Application
*
*
4x T1/E1/J1 + 10/100 Ethernet Copper to Fiber Transport Mux