Adtran XFP 10G 860nm 1442901G1 产品宣传页
产品代码
1442901G1
1
D
ESCRIPTION
The Small Form‐Factor Pluggable 10 Gigabit Multi‐Mode Fiber
XFP (MMF XFP) optical transceiver is a fully duplex serial
electric, serial optic device with both transmit and receive
functions contained in a single module that provides a high speed
serial link at 10 Gb/s. Installed into an appropriate host module,
the MMF XFP provides a 10 Gigabit interface to the supporting
system.
XFP (MMF XFP) optical transceiver is a fully duplex serial
electric, serial optic device with both transmit and receive
functions contained in a single module that provides a high speed
serial link at 10 Gb/s. Installed into an appropriate host module,
the MMF XFP provides a 10 Gigabit interface to the supporting
system.
The transmit side of the MMF XFP converts serial NRZ electrical
data at the10 Gb/s line rate to a standard compliant optical signal.
The receive side of the MMF XFP converts the incoming DC
balanced serial NRZ optical data at the 10 Gb/s line rate into serial
electrical data.
data at the10 Gb/s line rate to a standard compliant optical signal.
The receive side of the MMF XFP converts the incoming DC
balanced serial NRZ optical data at the 10 Gb/s line rate into serial
electrical data.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
with the host module.
The following features are supported on the MMF XFP:
♦
850 nm optical signals for up to 300 m reach
♦
Case temperature hardened range from –40°C to 85°C
♦
Bit error rate (<1x10
‐12
)
♦
Low power consumption (<1.5 W)
♦
Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, only XFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other XFPs.
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other XFPs.
Operational Specifications
♦
Optical Specifications:
◊
Transmit Wavelength: 840 nm to 860 nm
◊
Receive Wavelength: 840 nm to 860 nm
◊
Data rate: 9.95 Gb/s to 10.5 Gb/s
◊
Optical transmit level: –5.0d Bm to ‐1.0d Bm
Small Form-Factor Pluggable
10 Gigabit Multi-Mode Fiber XFP
◊
Optical receive level sensitivity: –11.1d Bm
◊
Optical distance: 300 m maximum
◊
Optical connectors: LC
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +85°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 85%, noncondensing
I
NSTALLATION
Inspect the MMF XFP. If damaged, file a claim with the carrier
and then contact ADTRAN Customer Service.
and then contact ADTRAN Customer Service.
To install the MMF XFP into an appropriate module, complete the
following steps:
following steps:
1. Insert the MMF XFP into the XFP cage on the circuit board of
the host module with the latch handle facing outward. Slide
the MMF XFP all the way into the receptacle.
the MMF XFP all the way into the receptacle.
NOTE
The latch on the MMF XFP is for removal only. When removing
the MMF XFP, rotate the latch away from the XFP cage until a
physical click occurs. The MMF XFP should slide easily out of the
cage.
the MMF XFP, rotate the latch away from the XFP cage until a
physical click occurs. The MMF XFP should slide easily out of the
cage.
2. Using thumb and forefinger, exert adequate pressure to
ensure the MMF XFP is completely seated in the XFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
NOTICE
It is recommended that the connector plug remain on whenever
the transceiver optical fiber connector is not inserted.
the transceiver optical fiber connector is not inserted.
4. Continue the installation and turn‐up of the host module
using the instructions in the Job Aid provided with that
module, or using the applicable Installation and
Maintenance Guide (I&M), available online at
module, or using the applicable Installation and
Maintenance Guide (I&M), available online at
www.adtran.com
.
P
ROVISIONING
The MMF XFP is not directly provisionable. To provision the
MMF XFP, access the menu system of the host module. Refer to
the “Provisioning” section of the Job Aid or Installation and
Maintenance Guide provided with the host module for provi‐
sioning details.
MMF XFP, access the menu system of the host module. Refer to
the “Provisioning” section of the Job Aid or Installation and
Maintenance Guide provided with the host module for provi‐
sioning details.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
Refer to the Small Form‐Factor Pluggable 10 Gigabit Multi‐Mode
Fiber XFP Safety and Regulatory Compliance Notice (P/N
61442901G1‐17) for detailed safety and regulatory information.
Fiber XFP Safety and Regulatory Compliance Notice (P/N
61442901G1‐17) for detailed safety and regulatory information.
CLEI: BVL3AFLD_ _
Product P/N: 1442901G1
Product P/N: 1442901G1
Issue Date: May 2010
Document P/N: 61442901G1-22A