Mobotix MX-OPT-NPA1-EXT 产品宣传页
The HiRes Video Company
EN
www
.mobotix.com
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-efficient.
decentralized concept has made high-resolution video systems cost-efficient.
MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-103 • Fax: +49 6302 9816-190 • sales@mobotix.com
MX-GPS-Box: Quick Install
Weatherproof GPS Time and
Position Information
• GPS time base for MOBOTIX cameras with MxBus
• New camera alarms available (position, speed,
• New camera alarms available (position, speed,
illumination, temperature)
• Remote installation (max. 50 m/55 yd wire length)
• Complete set including mounting supplies
• Complete set including mounting supplies
Reliable GPS time base for MOBOTIX systems,
includes outdoor temperature and illumination
sensors; connects via 2-wire cable
Connecting the MX-GPS-Box
Installation Instructions
1. Find a suitable mounting position
To guarantee optimum reception of the GPS signals by
the MX-GPS-Box, you should find a spot on the outside of
a building, which provides a clear view of the sky (max.
50 m/55 yd wire length between the MOBOTIX camera
and the MX-GPS-Box).
To guarantee optimum reception of the GPS signals by
the MX-GPS-Box, you should find a spot on the outside of
a building, which provides a clear view of the sky (max.
50 m/55 yd wire length between the MOBOTIX camera
and the MX-GPS-Box).
2. Attach the box
Attach the MX-GPS-Box at the mounting position with the
cable ports pointing downwards. Next, remove the box
cover (three screws).
Attach the MX-GPS-Box at the mounting position with the
cable ports pointing downwards. Next, remove the box
cover (three screws).
Do not remove the white sealing
plug (left) or the temperature sensor (center)!
3. Prepare the MxBus wires
Before proceeding, make sure there is no voltage on
the MxBus wires!
Cut the MxBus cable to size (2-wire, 0.6 to 0.8 mm diameter).
When using
Before proceeding, make sure there is no voltage on
the MxBus wires!
Cut the MxBus cable to size (2-wire, 0.6 to 0.8 mm diameter).
When using
wires without sheath, strip the insulation
of the wires for 5 mm and push the wires through the
eight-wire plug (right).
When using a
eight-wire plug (right).
When using a
cable with sheath, remove the pre-installed
eight-wire plug and insert the appropriate cable plug (3 to
5 mm or 5 to 7 mm). Press the rubber plug into the casing
in such a way that the rims stick out equally on both sides.
Push the cable through the plug, remove the sheath on
a length of 15 mm and strip the insulation of the wires
for about 5 mm.
5 mm or 5 to 7 mm). Press the rubber plug into the casing
in such a way that the rims stick out equally on both sides.
Push the cable through the plug, remove the sheath on
a length of 15 mm and strip the insulation of the wires
for about 5 mm.
4. Connect the MxBus wires to the terminal
Connect the MxBus wires to the screw terminals using
the screwdriver. Make sure to maintain the polarity (see
sticker in front of the terminal). Mount the cover back onto
the box (torque 0.4 Nm).
Connect the MxBus wires to the screw terminals using
the screwdriver. Make sure to maintain the polarity (see
sticker in front of the terminal). Mount the cover back onto
the box (torque 0.4 Nm).
5. Connect the MxBus wires to the opposite side
Connect the MxBus wires as described in the corresponding
manual to the MOBOTIX camera or to another MxBus module
connected to a camera (e.g. Keypad, Security Door Opener).
Make sure not to exceed the overall length of the MxBus
wiring of 50 m (55 yd).
Connect the MxBus wires as described in the corresponding
manual to the MOBOTIX camera or to another MxBus module
connected to a camera (e.g. Keypad, Security Door Opener).
Make sure not to exceed the overall length of the MxBus
wiring of 50 m (55 yd).
MxBus connector of
MOBOTIX D14
Initial Operation of a New IP Video Door Station T24
When installing a new MOBOTIX IP Video Door Station T24 for the first time, the MX-GPS-Box will be found
automatically when using the Autoconfiguration feature. In the process, the entire system will be set to use the
box as time server (see
automatically when using the Autoconfiguration feature. In the process, the entire system will be set to use the
box as time server (see
T24MX IP Video Door Station System Manual Part 2 on
www.mobotix.com).
75 mm/2.95 in
MX-GPS-Box
Drilling Template for the MX-GPS-Box
Drilling templates for other MOBOTIX components:
www
.mobotix.com > Support > Manuals
Protection class IP65
–30 to 60°C/–22 to 140°F
03/2012 • MX-OPT
-GPS1-EXT
MOBOTIX Camera
2-wire MxBus wiring to camera
(max. 50 m/55 yd)
MOBOTIX MX-GPS-Box
MX-OPT-GPS1-EXT
MOBOTIX IP Video Door Station T24
MX-T24M-Sec-D11
Temperature
sensor
Illumination
sensor