Transcend 256MB, DDR2, 667 SO-DIMM-200pin, 32Mx16, CL5 TS32MSQ64V6M 用户手册
产品代码
TS32MSQ64V6M
T
T
T
S
S
S
3
3
3
2
2
2
M
M
M
S
S
S
Q
Q
Q
6
6
6
4
4
4
V
V
V
6
6
6
M
M
M
200PIN DDR2 667 SO-DIMM
256MB With 32Mx16 CL5
Transcend Information Inc.
5
Absolute Maximum DC Ratings
Parameter
Symbol
Value
Unit
Notes
Voltage on V
DD
relative to Vss
VDD
-1.0 ~ 2.3
V
1
Voltage on V
DDQ
pin relative to Vss
VDDQ
-0.5 ~ 2.3
V
1
Voltage on V
DDL
pin relative to Vss
VDDL
-0.5 ~ 2.3
V
1
Voltage on any pin relative to Vss
VIN, VOUT
-0.5 ~ 2.3
V
1
Storage temperature
T
STG
-55~+100
°C 1,2
1.Stress greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the
stress rating only and functional operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect reliability.
in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect reliability.
Note:
2.Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the
measurement conditions, please refer to JESD51-2 standard.
AC & DC Operating Conditions
Recommended DC operating conditions (SSTL –1.8)
Rating
Parameter
Symbol
Min
Typ.
Max
Unit Notes
Supply voltage
VDD
1.7
1.8
1.9
V
Supply voltage for DLL
VDDL
1.7
1.8
1.9
V
4
Supply voltage for Output
VDDQ
1.7
1.8
1.9
V
4
I/O Reference voltage
VREF
0.49*VDDQ
0.50*VDDQ 0.51*VDDQ V
1,2
I/O Termination voltage
VTT
V
REF
-0.04 V
REF
V
REF
+0.04 V
3
DC Input logic high
VIH
(DC)
V
REF
+0.125
- V
DDQ
+0.3 V
DC Input logic low
VIL
(DC)
-0.3
- V
REF
-0.125 V
There is no specific device VDD supply voltage requirement for SSTL-1.8 compliance. However under all
conditions VDDQ must be less than or equal to VDD.
1.The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the
conditions VDDQ must be less than or equal to VDD.
1.The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the
value of VREF is expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track
variations in VDDQ.
variations in VDDQ.
2.Peak to peak AC noise on VREF may not exceed +/-2% VREF (DC).
3.VTT of transmitting device must track VREF of receiving device.
3.VTT of transmitting device must track VREF of receiving device.
Note:
4.AC parameters are measured with VDD, VDDQ and VDDDL tied together.
Operating Temperature Condition
Parameter
Symbol
Rating
Unit
Note
Operating Temperature
TOPER
0 to 85
°C
1,2
1.Operating Temperature is the case surface temperature on the center/top side of the DRAM. For the
measurement conditions, please refer to JESD51.2 standard.
2. At 0 - 85
°C, operation temperature range are the temperature which all DRAM specification will be supported.
Note: