Gefen VGA KVM over IP EXT-VGAKVM-LANR 产品宣传页

The VGA KVM over IP extends VGA, USB, 2-way analog audio, RS-232, and IR, 
over a Gigabit Local Area Network. Resolutions up to 1920 x 1200 (WUXGA) 
are supported. The Sender and Receiver units can be automatically or manually 
configured to unique IP addresses to allow the connection of multiple Senders 
and Receivers to the same network. Multiple Receiver units can simultaneously 
connect to any Sender unit within the network to create a virtual crosspoint matrix 
of up to 16 Senders and multiple Receivers up to a thoeritcal limit of just over 
65,000 units, depending on the network bandwidth and number of ports of the 
network switch.  Each Receiver unit has a built in Ethernet switch and two 
additional RJ-45 Ethernet ports to allow for the connection of computers and 
other IP-enabled devices. USB 2.0 data rates up to 480 Mbps are supported in 
addition to backward-compatibility with USB 1.1. Each Receiver unit allows the 
connection of two USB devices with up to 500mA current draw per port, 
providing access to keyboard, mouse, printers, and scanners, cameras. 
Bi-directional analog audio capability allows audio to be transported between 
the Sender and the Receiver units. Built-in mic pre-amp on the Receiver unit 
ensures compatibility with a variety of microphones. IR commands from the 
Receiver side can be extended to sources located by any of the Senders. 
RS-232 serial control can also be extended between each Sender and the 
Receivers. Built in web server interface makes set up and configuration simple 
and intuitive. The VGA KVM over IP is perfect for large scale remote workstation 
access, and for digital signage applications.

If you are connecting multiple Sender units, use the 16-position selector to assign 
a unique numerical ID to each one. Use the included VGA cable to connect a 
computer or other VGA source to the Sender’s VGA input. Use the included USB 
and RS-232 cables to connect your computer’s USB and RS-232 interfaces to the 
Sender unit. Connect audio Line In and audio Line Out as needed to the Sender.  
Connect a Gefen EXT-IR-EMIT IR emitter to the Sender and attach it to the IR 
sensor lens of the source. Connect the VGA output of the Receiver to your Hi-Def 
display.  Connect your USB devices, RS-232 devices, microphone, and 
headphones or amplified speakers to the Receiver unit. If the Receiver is not 
installed in the line-of-sight of the end-user, and IR commands will need to be 
sent to the source, connect an EXT-RMT-EXTIRC or EXT-RMT-EXTIRN extender 
module to the Receiver. Connect the Sender and Receiver units to each other 
directly or through a Gigabit Ethernet switch, using CAT-5e or better cables. 
Each cable run can be up to 330 feet (100 meters) in length.  If the Sender is 
connected to your LAN, you can use the two additional RJ-45 ports on the 
Receiver to connect computers and other IP enabled devices. Connect the 
included 5V power supplies to the Sender and Receiver units and to available 
electrical outlets. Power on all associated equipment. Use the Mode button on 
the Sender to optimize the picture for sharper still images or smoother video 
motion. Press the Switch button on the Receiver to toggle between the different 
Senders connected to the network.

NOTE:  A Gigabit LAN with 8k jumbo frame support is required. A dedicated 

LAN is not required, but highly recommended.

•  Extends VGA, USB, RS-232, bi-directional stereo analog audio, and IR over IP,        
    using a Gigabit Local Area Network
•  Supports resolutions up to 1920 x 1200 (WUXGA)
•  USB 2.0 data rates up to 480 Mbps and backward-compatibility with USB 1.1
•  Supports up to 16 Senders 
•  Supports just over 65,000 Receivers, depending on the network bandwidth and 
    number of ports of your network switch  
•  Three-port Ethernet switch built into the Receiver unit
•  Switch button on Receiver unit allows selection of multiple Senders
•  Mode button on Sender for sharpness or motion optimization of image
•  Field-upgradable firmware via web server interface
•  Locking power supply connectors
•  1U tall, half-rack width enclosures are rack-mountable using EXT-RACK-1U
•  Surface mounting brackets included

•  Maximum Video Bandwidth: 350 MHz
•  Video Input Connector (Sender): (1) VGA HD-15, female
•  Video Output Connector (Receiver): (1) VGA HD-15, female
•  Line Input (Sender): (1) 3.5mm mini-stereo jack
•  Line Output (Sender): (1) 3.5mm mini-stereo jack
•  Mic Input (Receiver): (1) 3.5mm mini-stereo jack
•  Line Output (Receiver): (1) 3.5mm mini-stereo jack
•  USB Host Interface (Sender): (1) USB Type B, female
•  USB Device Connectors (Receiver): (2) USB Type A, female
•  RS-232 Connector (Sender): (1) DB-9, female
•  RS-232 Connector (Receiver): (1) DB-9, male
•  IR Emitter (Sender): (1) 3.5mm mini-mono jack
•  IR Extender (Receiver): (1) 3.5mm mini-stereo jack
•  Ethernet connector (Sender): (1) RJ-45, shielded
•  Ethernet connectors (Receiver): (3) RJ-45, shielded
•  Mode button (Sender): (1) tact-type
•  ID Selector switch (Sender): (1) rotary-type
•  Switch button (Receiver): (1) tact-type
•  Reset button (Receiver): (1) tact-type, recessed
•  Link Indicator (Sender/Receiver): (1) LED, green
•  Power Indicator (Sender/Receiver): (1) LED, blue
•  Power Supply (Sender / Receiver): 5V DC, locking
•  Power Consumption (Sender / Receiver): 10W (max.)
•  Dimensions (Sender / Receiver) (W x H x D): 8.4” x 1.7” x 4.5”
                                                  (213mm x 43mm x 113mm)
•  Unit Weight: 7 lbs. (3.2 kg)

VGA and KVM Extender over IP

EXT-VGAKVM-LAN

* Features and specifications subject to change without notice.

    

REV. A1

All trademarks and registered trademarks are properties of their respective owners.