MEAN WELL ELN-60-24 用户手册

12V

6 ~ 12V

5A

9V

15V

7.5 ~ 15V

24V

12 ~ 24V

48V

24 ~ 48V

5A

2.5A

2.3A

27V

13.5 ~ 27V

1.3A

0 ~ 5A

0 ~ 5A

0 ~ 4A

4A

0 ~ 2.5A

0 ~ 2.3A

0 ~ 1.3A

60W

45W

60W

60W

62.1W

62.5W

120mVp-p

10.8 ~ 13.2V

120mVp-p

150mVp-p

13.5 ~ 16.5V

150mVp-p

21.6 ~ 26.4V

200mVp-p

24.3 ~ 29.7V

250mVp-p

43.2 ~ 52.8V

¡Ó5.0%

-25% ~ 3%. Can be adjusted by internal potentiometer SVR2

¡Ó1.0%
¡Ó2.0%
500ms, 30ms / 230VAC 15

at full load

00ms, 30ms / 115VAC

90 ~ 264VAC

127 ~ 370VDC

47 ~ 63Hz

82%

85%

86%

87%

87%

88%

13.8 ~ 16V

11 ~ 13.5V

17.5 ~ 21V

28 ~ 32V

31 ~ 37V

54 ~ 60V

1.2A/115VAC

0.7A/230VAC

0.25mA / 240VAC

Protection type : Constant current limiting, recovers automatically after fault condition is removed

-20 ~ +60

¢J (Refer to "Derating Curve")

20 ~ 90% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

¢J

¡Ó

¢J

¢J

0.03%/

(0 ~ 50

)

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

603K hrs min.

MIL-HDBK-217F (25

)

¢J

181*61.5*35mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB.
8. Constant current operation region is within the specified output voltage range above. This is the suitable operation region for LED related applications.
9. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.

¢J

0.4Kg; 24pcs/11Kg/0.75CUFT

60W Single Output Class 2 Switching Power Supply

Universal AC input / Full range
Protections: Short circuit / Over current / Over voltage
Cooling by free air convection
Built-in constant current limiting circuit with adjustable OCP level
Optional dimming function : 1~10VDC (D type) or PWM (P type) controlled
Fully isolated plastic case with IP64 level

Class 2 power unit
Pass LPS
Suitable for LED lighting and moving sign applications (Note.9)
100% full load burn-in test
Low cost, high reliability
2 years warranty

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¡E

¢º

Class

power unit, no FG

¡½

Features :

I/P-O/P:3KVAC

I/P-O/P:>100M Ohms / 500VDC / 25

/ 70% RH

¢J

Compliance to EN55022 (CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A

8.7 ~ 10.5V

UL1310, CAN/CSA C22.2 No. 223-M91(except for 48V), IP64 approved ; design refer to TUV EN60950-1

95 ~ 110%

Protection type : Shut down o/p voltage, re-power on to recover

50ms/230VAC

16ms/115VAC at full load

1 ~ 10VDC or PWM signal : 100Hz ~ 3KHz

3 ~ 9V

Can be adjusted by internal potentiometer SVR1

( for 48V only)

( except for 48V )

COLD START 60A(t

=600 s measured at 50% I

) at 230VAC

width

peak

£g