Sound Blaster MP3 Player Speaker, Black 51MF8170AA005 产品宣传页

1
2

LS

1
2

L

S

1.   NFC Receptor
2.   Battery  Indicator
3.   Record Indicator
4.   Power / Bluetooth

®

 Status Indicator

5.   Multifunction Button
 - 

For 

Bluetooth pairing / connecting

 - 

Answering 

calls

6.   Volume Up / Down Button
7.               Button
 

- Increases overall loudness and spaciousness 

for maximum audio output

8.   Power ON / Standby Button
9.   Microphone

PN: 03MF817000009 Rev A

2

3

5

6

7

8

1

10. DC Input
11. Aux-In
12. DC Out (USB 1.0A)
13. Micro USB Connector
14. MicroSD Slot
15. Mic On / Mute Switch
16. Record Button
17. (Record) Play / Pause Button

18. Shuffle / Repeat All Switch
19. Previous Button
20. Next Button
21. (MP3 Playback) Play / Pause Button
22. OFF / (1) Loud Sounds Mode 1 / 
 

(2) Loud Sounds Mode 2 Switch 

23. Alarm Button
24. (Alarm) Arm / Off Switch

15 17

18 20

24

22

16

19 21

23

11

12

13 14

10

1

2

L

S

Overview

NOTE:
Power saving mode: The speaker automatically powers down when there is no Bluetooth connection, 
recording using microSD card, microSD card playback or audio input for more than 15 minutes.

For optimized charging: Creative recommends using the bundled USB cable for optimized charging.

TIP:
Lithium-ion battery life may suffer when it is constantly fully depleted or overexerted at low voltage. 
It is a good practice to keep the battery well charged.

Battery at about 70%

Battery low

Battery full

Battery extremely low

Battery charging

Running LED

Slow Blink

Charge the speaker with the supplied power adapter for at least 3 hours 
before use. Please ensure your speaker is powered off for optimized charging.
*Battery performance may degrade over time depending on charge cycles.

3 Hours

The Sound Blaster ROAR can also be charged using a USB cable. It may take longer 
to charge due to USB power limitation. Switch off your speaker when charging. 

PC/Mac

Mains

1

11

* Not included, USB 

adapter with DC 5V 
and up to 1A output 
rating can be used.

- Supplied interchangeable plugs may vary according to region and country.

1. Press the Power ON / Standby button to 

power ON the speaker.

2. Press and hold the Multifunction button 

until the white LED is blinking rapidly.

3. Select  SB ROAR SR20 from the list of 

discovered Bluetooth devices, and they’re 
paired!

Turn on NFC on your NFC-enabled device and tap your device on the NFC logo to connect.
To disconnect, tap your device on the Sound Blaster Roar again.

Green LED stays lit

White LED blinking 
rapidly

White LED stays lit

Powered ON but not 
connected to any 
Bluetooth devices
Bluetooth Pairing 
Mode, waiting for 
device to connect
Connected to a 
Bluetooth device

2

2

NOTE:
Be sure that your phone is NFC-enabled and find out where the NFC sensor is located on your phone. 
For more information, refer to the User Guide of your phone.

TIP:
With Multipoint, you can connect up to two smart devices with your speaker simultaneously. 
Simply pause the playback on your current device and tap another device to connect!

* The speaker automatically goes into MicroSD Card Reader Mode every time it is connected 

to a computer. To use it for audio playback, see “Playing audio from computer (USB audio)”.

Information in this document is subject to change without notice and does not represent a commitment on the part of Creative Technology Ltd. 
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and 
recording, for any purpose without the written permission of Creative Technology Ltd.

Copyright © 2014 Creative Technology Ltd. All rights reserved. Creative, the Creative logo, Sound Blaster, the Sound Blaster logo, Sound 
Blaster Roar, SBX Pro Studio and the SBX Pro Studio logo are trademarks or registered trademarks of Creative Technology Ltd. in the United 
States and/or other countries. The Bluetooth

®

 word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of 

such marks by Creative Technology Ltd is under license. Other trademarks and trade names are those of their respective owners. aptX is a 
trademark of CSR Plc. microSDHC Logo is a trademark of SD-3C, LLC. All specifications are subject to change without prior notice. Use of this 
product is subject to a limited hardware warranty. Actual contents may differ slightly from those pictured. The software included in this 
packaging may not be used separately from the hardware. Before using the software, you must agree to be bound by the terms and conditions 
of the end user license agreement.

9

1
2

L

S

4

creative.com

Supplementary documentation for this product includes a DoC and safety and regulatory 
information. These documents can be downloaded on the www.creative.com/support site.

Complies with 

IDA Standards 

DB00148