AEG AR 4021 BT 400402 用户手册

86

This chapter gives important operating instructions for 

the unit.

 

Several buttons can be found on the unit as well as 

 

►

on the remote control. Identical buttons perform the 

same function. The buttons appear in the following 

text are the buttons on the unit.

The remote control signals are sent to the unit via 

 

►

infrared light. The transmission of the signals from 

the remote control to the unit may be impaired by 

direct sunlight on the IR sensor (6).

Press the button 

 

‹

/MUT (2) to switch on the set. The 

display is activated.

Hold down the 

 

‹

/MUT (2) button to switch the unit 

off.

 

High volumes can permanently damage your hearing.

Set a moderate volume.

 

►

Press the 

 

‹

/  buttons (23) to adjust the volume.

Press the 

 

‹

/MUT (2) button to switch the unit to 

mute. 

MUTE flashes on the display.

Press the 

 

‹

/MUT (2) button again to deactivate the 

function.

Press the 

 

‹

SEL button (5). The current volume is dis-

played. Press the 

SEL button again to open the next 

setting.

The following settings are possible:

VOL  -  volume (0 to 100)

BAS  -  bass (-10 to +10)

TRB  -  treble (-10 to +10)

BAL  -  Balance (sound distribution between left and 

right speakers) (10L to 10R)

FAD  -  Fader (sound distribution between rear and front 

speakers) (10F to 10R)

Press the 

 

‹

/  buttons (23), to change the displayed 

setting.

Keep the 

 

‹

SEL button (5) pressed for a few seconds to 

open more settings options. Press the 

SEL button again 

to open the next setting.

Press the 

 

‹

/  buttons (23), to change the displayed 

setting.

The following settings are possible:

Key tone:

■

The unit sounds a beep tone 

every time you press a button.

■

The unit sounds no beep tone.

Adjusts the volume at which the unit should 

switch on.

Region, when the unit is used.

Europe (

EUR) or USA

 

Changing this setting deletes all station 

 

►

presets.

Select the time display here.

24 hour (24 H) or 12 hour (12 H)

 

If 12 hours is selected, the display shows: 

 

►

AM = morning, PM = afternoon.

Select here if the time should be displayed 

when the unit is switched off.

Keep the 

 

‹

PTY button (17) pressed for several seconds 

to open more setting options. Press the 

PTY button 

again to open the next setting.

Press the 

 

‹

/  buttons (23) to change the displayed 

setting.

The following settings are possible:

Traffic announcements

■

With activated TA function the 

unit searches for a station with traffic an-

nouncements.

■

 No automatic station search. 

The unit sounds a beep tone if no traffic 

information is received and 

NO TP/TA is dis-

played. 

SEEK PI is displayed if the selected 

station does not transmit an RDS signal.

Moving into an area where two stations 

with identical AF, but different Pl code (PI = 

program information) are received destabilizes 

reception. In this situation you have two op-

tions:

■

 To change stations the other 

station is played for less than one second.

■

 The other station is muted.

RETUNE Delay for automatic search with traffic an-

nouncements and/or program information:

■  (Short) after approx. 30 seconds

■  (Long) after approx. 90 seconds