MEAN WELL CLG-60-24 数据表

12V

15V

20V

24V

27V

36V

48V

0 ~ 5A

0 ~ 4A

0 ~ 3A

0 ~ 2.5A

0 ~ 2.3A

0 ~ 1.7A

0 ~ 1.3A

60W

60W

60W

60W

62.1W

61W

62.5W

2Vp-p

2.4Vp-p

1.8Vp-p

2.7Vp-p

2.7Vp-p

3.6Vp-p

4.6Vp-p

10%

Fixed can be modified between the range above

Fixed. Can be modified between 3% ~ -25% rated output current

3.0%

5.0%

3000ms / 230VAC 5000ms / 115VAC at full load

90 ~ 295VAC

127 ~ 417VDC

47 ~ 63Hz

PF

0.9 at 75 ~ 100% load, 115VAC / 230VAC

85%

86%

87.5%

87%

88%

89%

89%

13.8 ~ 16V

17.5 ~ 21V

23 ~ 26V

28 ~ 32V

31 ~ 35V

41 ~ 46V

54 ~ 60V

0.8A/115VAC

0.4A/230VAC

40A/230VAC

<0.75mA / 240VAC

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed

-30 ~ +70

(Refer to output load derating curve)

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

0.03%/

(0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

495.7Khrs min.

MIL-HDBK-217F (25

)

195.6*61.5*38.8mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

Direct connecting to LEDs is not suggested for models with “RIPPLE & NOISE”  > 10% and using additional drivers is highly recommended.

3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

0.86Kg; 16pcs/14.8Kg/0.54CUFT

Protection type : Shut down o/p voltage, re-power on to recover

60W Single Output LED Power Supply

Universal AC input / Full range

Protections: Short circuit / Overload / Over voltage / Over temperature
Built-in active PFC function
IP67 design for indoor or outdoor installations
UL1310 Class 2 power unit
Pass LPS
Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting

3 years warranty

(up to 295VAC)

Suitable for dry / damp / wet locations

(Note.2)

High efficiency 89%

Features :

12V: 90

10

(TSW1) detect on heatsink of power transistor

15V ~ 48V: 85

10

(TSW1) detect on heatsink of power transistor

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

I/P-O/P:3.75KVAC

I/P-FG:1.88KVAC

O/P-FG:0.5KVAC

UL879, UL8750, UL1310 Class 2, TUV EN61347-1, EN61347-2-13 independent, CAN/CSA C22.2 No. 223-M91(except for 48V) ;

J61347-1, J61347-2-13(20~27only), IP67 approved

I/P-O/P:100M Ohms / 500VDC / 25

/ 70% RH

Compliance to EN55015, EN55022 (CISPR22) Class B

Compliance to

Class C (

75% load) ; EN61000-3-3

EN61000-3-2

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN61547, light industry level (surge 4KV), criteria A

10.5 ~ 15V

14 ~ 20V

16.8 ~ 24V

18.9 ~ 27V

25.2 ~ 36V

33.6 ~ 48V

8.4 ~ 12V

5A

4A

3A

2.5A

2.3A

1.7A

1.3A

11.5 ~ 13V

14.5 ~ 16.2V

19.5 ~ 22V

24 ~ 26V

25 ~ 30V

32.5 ~ 39V

43.6 ~ 51.8V

( for 48V only)

( except for 48V )

( for 20~27V only)