Hameg HZO50Clip-on ammeter adapter 17-O050-0000 数据表
产品代码
17-O050-0000
HZO10/20/30/50/51E/240112 · C&E · Subject to change without notice · © HAMEG Instruments GmbH
®
· DQS-certified in accordance with DIN EN ISO 9001:2008, Reg.-No.: 071040 QM08
HAMEG Instruments GmbH · Industriestr. 6 · D-63533 Mainhausen · Tel +49 (0) 6182 8000 · Fax +49 (0) 6182 800100 · www.hameg.com · info@hameg.com
This AC/DC current probe is used to measure currents from 1 mA
to 30 A over a broad frequency range. The measure ment principle is
based on the Hall Effect that registers the magnetic field generated
by the current flow. Even for complex waveforms a high degree of
measurement accu racy is achieved. The output voltage is propor-
tional to the measured current and well suited to be displayed on
an oscilloscope. The current probe complies with the safety stand-
ards defined in IEC/EN 61010.
to 30 A over a broad frequency range. The measure ment principle is
based on the Hall Effect that registers the magnetic field generated
by the current flow. Even for complex waveforms a high degree of
measurement accu racy is achieved. The output voltage is propor-
tional to the measured current and well suited to be displayed on
an oscilloscope. The current probe complies with the safety stand-
ards defined in IEC/EN 61010.
Specifications
Measurement range:
±20 A
rms
/30 A
p
Accuracy:
±1 % from measurement value ±2 mA
Bandwidth:
DC…100 kHz (0.5 dB)
Resolution:
±1 mA
Output Voltage:
100 mV/A
Load impedance:
>100 kΩ II ≤100 pF
Max. Voltage:
300 V
rms
(AC or DC)
Output cable/Connector: 2 m (50 Ω)/BNC
Measuring category:
CAT III
H Z O 5 0 A C / D C C u r r e n t P r o b e 3 0 A
This AC/DC current probe is used to measure currents from 100 mA
to 1000 A over a broad frequency range. The measure ment prin-
ciple is based on the Hall Effect that registers the magnetic field
to 1000 A over a broad frequency range. The measure ment prin-
ciple is based on the Hall Effect that registers the magnetic field
generated by the current flow. Even for complex waveforms a high
degree of measurement accu racy is achieved. The output voltage
is proportional to the measured current and well suited to be dis-
played on an oscilloscope. The current probe complies with the
degree of measurement accu racy is achieved. The output voltage
is proportional to the measured current and well suited to be dis-
played on an oscilloscope. The current probe complies with the
safety standards defined in IEC/EN 61010.
Specifications
Measurement range:
±100 A
rms
/1000 A
rms
Accuracy:
±1 % from measurement value ±0.1 A/±0.5 A
Bandwidth:
DC…20 kHz
Resolution:
±100 mA/±500 mA
Output Voltage:
10 mV/A/1 mV/A
Load impedance:
>100 kΩ II ≤100 pF
Max. Voltage:
300 V
rms
(AC or DC)
Output cable/Connector: 2 m (50 Ω)/BNC
Measuring category:
CAT III
H Z O 5 1 A C / D C C u r r e n t P r o b e 1 0 0 A / 1 0 0 0 A
Current measurement
with HMO
with HMO
Current measurement
with HMO
with HMO