Microchip Technology IC MCU FLASH 4K PIC16LF88-I/P DIP-18 MCP PIC16LF88-I/P 数据表
产品代码
PIC16LF88-I/P
PIC16F87/88
DS30487D-page 174
2002-2013 Microchip Technology Inc.
V
OL
Output Low Voltage
D080
I/O ports
—
—
0.6
V
I
OL
= 8.5 mA, V
DD
= 4.5V,
-40
C to +125C
D083
OSC2/CLKO
(RC oscillator configuration)
(RC oscillator configuration)
—
—
0.6
V
I
OL
= 1.6 mA, V
DD
= 4.5V,
-40
C to +125C
V
OH
Output High Voltage
D090
I/O ports (Note 3)
V
DD
– 0.7
—
—
V
I
OH
= -3.0 mA, V
DD
= 4.5V,
-40
C to +125C
D092
OSC2/CLKO
(RC oscillator configuration)
(RC oscillator configuration)
V
DD
– 0.7
—
—
V
I
OH
= -1.3 mA, V
DD
= 4.5V,
-40
C to +125C
Capacitive Loading Specs on Output Pins
D100
C
OSC2
OSC2 pin
—
—
15
pF
In XT, HS and LP modes
when external clock is used
to drive OSC1
when external clock is used
to drive OSC1
D101
C
IO
All I/O pins and OSC2
(in RC mode)
(in RC mode)
—
—
50
pF
D102
C
B
SCL, SDA in I
2
C™ mode
—
—
400
pF
Data EEPROM Memory
D120
E
D
Endurance
100K
10K
1M
100K
—
—
—
E/W
E/W
E/W
-40
C to 85C
+85
C to +125C
D121
V
DRW
V
DD
for Read/Write
V
MIN
—
5.5
V
Using EECON to read/write,
V
V
MIN
= min. operating voltage
D122
T
DEW
Erase/Write Cycle Time
—
4
8
ms
Program Flash Memory
D130
E
P
Endurance
10K
1K
100K
10K
—
—
—
E/W
E/W
E/W
-40
C to 85C
+85
C to +125C
D131
V
PR
V
DD
for Read
V
MIN
—
5.5
V
D132A
V
DD
for Erase/Write
V
MIN
—
5.5
V
Using EECON to read/write,
V
V
MIN
= min. operating voltage
D133
T
PE
Erase Cycle Time
—
2
4
ms
D134
T
PW
Write Cycle Time
—
2
4
ms
18.4
DC Characteristics:
PIC16F87/88 (Industrial, Extended)
PIC16LF87/88 (Industrial) (Continued)
PIC16LF87/88 (Industrial) (Continued)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating temperature
-40°C
T
A
+85°C for industrial
-40°C
T
A
+125°C for extended
Operating voltage V
DD
range as described in DC Specification,
Section 18.1 “DC Characteristics: Supply Voltage”.
Param
No.
Sym
Characteristic
Min
Typ†
Max
Units
Conditions
*
These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1:
In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the
PIC16F87/88 be driven with external clock in RC mode.
PIC16F87/88 be driven with external clock in RC mode.
2:
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3:
Negative current is defined as current sourced by the pin.