Texas Instruments Evaluation Module for TPS6236 TPS62362EVM-655 TPS62362EVM-655 数据表
产品代码
TPS62362EVM-655
Setup
Table 1. Performance Specification Summary (continued)
SPECIFICATION
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Maximum efficiency
V
IN
= 3.6V, V
OUT
= 1.7V, I
OUT
= 750mA
91.4%
2
Setup
This section describes the jumpers and connectors on the EVM as well as how to properly connect, set
up, and use the TPS6236xEVM-655.
up, and use the TPS6236xEVM-655.
2.1
Connector/Jumper Descriptions
2.1.1
J1
–
V
IN
This header is for the positive input supply voltage to the converter. The leads to the input supply should
be twisted and kept as short as possible to minimize EMI transmission and reduce inductive voltage droop
at a load transient event. This voltage should be between 2.5V and 5.5V.
be twisted and kept as short as possible to minimize EMI transmission and reduce inductive voltage droop
at a load transient event. This voltage should be between 2.5V and 5.5V.
2.1.2
J2
–
S+/S-
Sense connector for V
IN
. Connect input supply's sense leads to this point. Monitor the V
IN
voltage at this
point.
2.1.3
J3
–
GND
This is the return connection for the input power supply of the converter. The leads to the input supply
should be twisted and kept as short as possible to minimize EMI transmission and reduce inductive
voltage droop at a load transient event.
should be twisted and kept as short as possible to minimize EMI transmission and reduce inductive
voltage droop at a load transient event.
2.1.4
J4
–
V
OUT
This header connects to V
OUT
. Connect the load (processor) at this point if the load current will remain
below 1A. If the load current will exceed 1A, use terminal block J7 instead. The leads to the load should
be twisted and kept as short as possible to minimize EMI transmission and reduce inductive voltage droop
at a load transient event.
be twisted and kept as short as possible to minimize EMI transmission and reduce inductive voltage droop
at a load transient event.
2.1.5
J5
–
SNS+/SNS-
Remote sense connector for the IC. For proper regulation, this must be connected at the load. This is
a high impedance connection back to the TPS6236x's remote sense inputs and is required for output
regulation. Monitor the output voltage at this point.
a high impedance connection back to the TPS6236x's remote sense inputs and is required for output
regulation. Monitor the output voltage at this point.
2.1.6
J6
–
GND
This is the return connection for the load. If the load current will exceed 1A, do not use headers J4 and J6,
but use terminal block J7 instead. The leads to the load should be twisted and kept as short as possible to
minimize EMI transmission and reduce inductive voltage droop at a load transient event.
but use terminal block J7 instead. The leads to the load should be twisted and kept as short as possible to
minimize EMI transmission and reduce inductive voltage droop at a load transient event.
2.1.7
J7
–
V
OUT
/GND Terminal Block
This terminal block should be used to connect to the load (processor) if the load current will exceed 1A. If
the load current will remain below 1A, the J4/J6 headers may be used instead. The leads to the load
should be twisted and kept as short as possible to minimize EMI transmission and reduce inductive
voltage droop at a load transient event.
the load current will remain below 1A, the J4/J6 headers may be used instead. The leads to the load
should be twisted and kept as short as possible to minimize EMI transmission and reduce inductive
voltage droop at a load transient event.
2.1.8
J8
–
I
2
C Connection from USB-TO-GPIO Adaptor
This connects the USB-TO-GPIO adaptor to the TPS6236xEVM-655. It provides the I
2
C signals and a
3.3V supply for powering V
DD
. If the USB-TO-GPIO adaptor is not used, do not connect to J8, but connect
the I
2
C signals to the J9 header instead. This connector is keyed to prevent incorrect installation.
3
SLVU425A
–
April 2011
–
Revised July 2011
TPS6236xEVM-655
Copyright
©
2011, Texas Instruments Incorporated