Texas Instruments BOOSTXL-SENSHUB 用户手册
Hardware Description
2.1
Functional Description
This section provides a functional description of the Sensor Hub BoosterPack.
2.1.1
BoosterPack XL Connector
The BoosterPack XL connector attaches the BoosterPack to the Tiva TM4C LaunchPad. This
BoosterPack is specifically designed to match the pin function with the Tiva TM4C LaunchPad. Basic I
BoosterPack is specifically designed to match the pin function with the Tiva TM4C LaunchPad. Basic I
2
C
and UART communication to the sensors and RF expansion connectors are also available when the
Sensor Hub is connected to either the
Sensor Hub is connected to either the
describes the BoosterPack XL interface connections and the respective uses on the Sensor Hub
BoosterPack. It also shows which pins remain available for additional expansion at the user's discretion.
Table 2. BoosterPack XL Interface Connections
(1)
Pin
Function
Pin
Function
Pin
Function
Pin
Function
J1.1
3.3 V IN
J2.1
Ground
J3.1
J4.1
J1.2
J2.2
Interrupt
J3.2
J4.2
J1.3
UART RX
J2.3
Interrupt
J3.3
J4.3
RF GPIO
J1.4
UART TX
J2.4
J3.4
J4.4
UART RTS
J1.5
J2.5
J3.5
USER LED
J4.5
UART CTS
J1.6
Interrupt
J2.6
Sensor I2C
J3.6
User Button
J4.6
RF Shutdown
J1.7
J2.7
Sensor I2C
J3.7
User Button
J4.7
RF Reset
J1.8
SSI TX
J2.8
SSI RX
J3.8
RF GPIO
J4.8
RF GPIO
J1.9
RF I2C
J2.9
SSI SS
J3.9
RF GPIO
J4.9
J1.10
RF I2C
J2.10
SSI CLK
J3.10
J4.10
(1)
Shaded cells indicate unused pins that are available for additional expansion.
2.1.2
TMP006 Temperature Sensor
The TMP006 provides both direct and indirect temperature measurements. It contains an on-chip
temperature sensor to directly measure ambient temperature conditions. It also allows contactless infrared
object temperature measurement.
temperature sensor to directly measure ambient temperature conditions. It also allows contactless infrared
object temperature measurement.
2.1.3
InvenSense MPU9150 9-Axis Motion Sensor
The MPU9150 is a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer in a single package.
This device is the primary motion sensor on the Sensor Hub. It is used by the demonstration software as
the raw motion inputs, which are fused by a direct cosine matrix into roll, pitch, and yaw measurements.
This device is the primary motion sensor on the Sensor Hub. It is used by the demonstration software as
the raw motion inputs, which are fused by a direct cosine matrix into roll, pitch, and yaw measurements.
2.1.4
Intersil ISL29023 Ambient and Infrared Light Sensor
The ISL29023 provides sensor measurements of light conditions across both the ambient (human-visible)
spectrum and the infrared spectrum.
spectrum and the infrared spectrum.
2.1.5
Sensirion SHT21 Humidity Sensor
The SHT21 provides relative humidity measurements.
2.1.6
Bosch BMP180 Barometric Pressure Sensor
The BMP180 measures barometric pressure conditions. It can be used to enhance the motion sensor by
determining relative changes in altitude.
determining relative changes in altitude.
2.1.7
Low-Power RF Expansion Connection
The RF expansion connection provides a wide array of options to the end application.
4
BOOSTXL-SENSHUB Sensor Hub BoosterPack
SPMU290 – April 2013
Copyright © 2013, Texas Instruments Incorporated